序号

标准号

标准英文名称

1

ISO 161-1:2018

Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series

2

 ISO 161-2:1996

Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch-based series

3

ISO 265-1:1988

Pipes and fittings of plastics materials — Fittings for domestic and industrial waste pipes — Basic dimensions: Metric series — Part 1: Unplasticized poly(vinyl chloride) (PVC-U)

4

ISO 1167-1:2006

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method

5

ISO 1167-2:2006

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces

6

ISO 1167-3:2007

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 3: Preparation of components

7

ISO 1167-4:2007

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies

8

ISO 1452-1:2009

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: General

9

ISO 1452-2:2009

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Pipes

10

ISO 1452-3:2009

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 3: Fittings

11

ISO 1452-4:2009

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 4: Valves

12

ISO 1452-5:2009

Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 5: Fitness for purpose of the system

13

ISO 2505:2005

Thermoplastics pipes — Longitudinal reversion — Test method and parameters

14

ISO 2507-1:1995

Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method

15

ISO 2507-2:1995

Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes

16

ISO 2507-3:1995

Thermoplastics pipes and fittings — Vicat softening temperature — Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings

17

ISO 3114:1977

Unplasticized polyvinyl chloride (PVC) pipes for potable water supply — Extractability of lead and tin — Test method

18

ISO 3126:2005

Plastics piping systems — Plastics components — Determination of dimensions

19

ISO 3127:1994

Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method

20

ISO 3213:2009

Polypropylene (PP) pipes — Effect of time and temperature on the expected strength

21

ISO 3514:1976

Chlorinated polyvinyl chloride (CPVC) pipes and fittings — Specification and determination of density

22

ISO 3633:2002

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Unplasticized poly(vinyl chloride) (PVC-U)

23

ISO 4059:1978

Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements

24

ISO 4065:2018

Thermoplastics pipes — Universal wall thickness table

25

ISO/TR 4191:2014

Plastics piping systems for water supply — Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) — Guidance for installation

26

ISO 4427-1:2019

Plastics piping systems for water supply and for drainage and sewerage under pressure — Polyethylene (PE) — Part 1: General

27

ISO 4427-2:2019

Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 2: Pipes

28

ISO 4427-5:2019

Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 5: Fitness for purpose of the system

29

ISO 4433-1:1997

Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method

30

ISO 4433-2:1997

Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes

31

ISO 4433-3:1997

Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 3: Unplasticized poly(vinyl chloride) (PVC-U), high-impact poly (vinyl chloride) (PVC-HI) and chlorinated poly (vinyl chloride) (PVC-C) pipes

32

ISO 4433-4:1997

Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 4: Poly(vinylidene fluoride) (PVDF) pipes

33

ISO 4435:2003

Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U)

34

ISO 4439:1979

Unplasticized polyvinyl chloride (PVC) pipes and fittings — Determination and specification of density

35

ISO 6259-1:2015

Thermoplastics pipes — Determination of tensile properties — Part 1: General test method

36

ISO 6259-2:1997

Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)

37

ISO 6259-3:2015

Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes

38

ISO/DIS 6259-2

Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride (PVC-O), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)

39

ISO 6964:2019

Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method

40

ISO/TS 7024:2005

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Thermoplastics — Recommended practice for installation

41

ISO/WD TR 7024

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Thermoplastics — Recommended practice for installation

42

ISO 7245:1984

Pipes and fittings of acrylonitrile/butadiene/styrene (ABS) — General specification for moulding and extrusion materials

43

ISO 7246:1984

Pipes and fittings of acrylonitrile/styrene/acrylester (ASA) — General specification for moulding and extrusion materials

44

ISO 7432:2018

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals

45

ISO 7509:2015

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of time to failure under sustained internal pressure

46

ISO 7510:2017

Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents

47

ISO 7511:1999

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the leaktightness of the wall under short-term internal pressure

48

ISO 7671:2003

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Polypropylene (PP)

49

ISO 7675:2003

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Chlorinated poly(vinyl chloride) (PVC-C)

50

ISO 7682:2003

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Acrylonitrile-butadiene-styrene (ABS)

51

ISO 7685:2019

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial ring stiffness

52

ISO 7686:2005

Plastics pipes and fittings — Determination of opacity

53

ISO 8283-1:1991

Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 1: Unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C)

54

ISO 8283-2:1992

Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 2: Polyethylene (PE)

55

ISO 8283-3:1992

Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 3: Polypropylene (PP)

56

ISO 8283-4:1992

Plastics pipes and fittings — Dimensions of sockets and spigots for discharge systems inside buildings — Part 4: Acrylonitrile/butadiene/styrene (ABS)

57

ISO 8361-1:1991

Thermoplastics pipes and fittings — Water absorption — Part 1: General test method

58

ISO 8361-2:1991

Thermoplastics pipes and fittings — Water absorption — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings

59

ISO 8361-3:1991

Thermoplastics pipes and fittings — Water absorption — Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) pipes and fittings

60

ISO 8483:2019

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints

61

ISO 8513:2016

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength

62

ISO 8521:2009

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the apparent initial circumferential tensile strength

63

ISO 8533:2019

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of cemented or wrapped joints

64

ISO 8770:2003

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Polyethylene (PE)

65

ISO 8772:2006

Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE)

66

ISO 8773:2006

Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP)

67

ISO 8779:2010

Plastics piping systems — Polyethylene (PE) pipes for irrigation — Specifications

68

ISO 8779:2010/AMD 1:2014

Plastics piping systems — Polyethylene (PE) pipes for irrigation — Specifications — Amendment 1

69

ISO 8795:2001

Plastics piping systems for the transport of water intended for human consumption — Migration assessment — Determination of migration values of plastics pipes and fittings and their joints

70

ISO 8796:2004

Polyethylene PE 32 and PE 40 pipes for irrigation laterals — Susceptibility to environmental stress cracking induced by insert-type fittings — Test method and requirements

71

ISO 9080:2012

Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation

72

ISO 9852:2007

Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method

73

ISO 9854-1:1994

Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 1: General test method

74

ISO 9854-2:1994

Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 2: Test conditions for pipes of various materials

75

ISO 9896:1996

Plastics traps for discharge pipework systems inside buildings

76

ISO 9967:2016

Thermoplastics pipes — Determination of creep ratio

77

ISO 9969:2016

Thermoplastics pipes — Determination of ring stiffness

78

ISO 10146:2019

Crosslinked polyethylene (PE-X) and crosslinked medium density polyethylene (PE-MDX) — Effect of time and temperature on expected strength

79

ISO 10147:2011

Pipes and fittings made of crosslinked polyethylene (PE-X) — Estimation of the degree of crosslinking by determination of the gel content

80

ISO/TR 10358:1993

Plastics pipes and fittings — Combined chemical-resistance classification table

81

ISO 10466:1997

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test method to prove the resistance to initial ring deflection

82

ISO 10467:2018

Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

83

ISO 10468:2018

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions

84

ISO 10471:2018

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions

85

ISO/TR 10501:1993

Thermoplastics pipes for the transport of liquids under pressure — Calculation of head losses

86

ISO 10508:2006

Plastics piping systems for hot and cold water installations — Guidance for classification and design

87

ISO 10508:2006/AMD 1:2018

Plastics piping systems for hot and cold water installations — Guidance for classification and design — Amendment 1

88

ISO 10639:2017

Plastics piping systems for pressure and non-pressure water supply — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

89

ISO 10928:2016

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use

90

ISO 10952:2014

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition

91

ISO 11173:1994

Thermoplastics pipes — Determination of resistance to external blows — Staircase method

92

ISO 11296-1:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General

93

ISO 11296-2:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 2: Lining with continuous pipes

94

ISO 11296-3:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 3: Lining with close-fit pipes

95

ISO 11296-4:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes

96

ISO 11296-7:2019

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes

97

ISO 11297-1:2018

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 1: General

98

ISO 11297-2:2018

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continuous pipes

99

ISO 11297-3:2018

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 3: Lining with close-fit pipes

100

ISO 11297-4:2018

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 4: Lining with cured-in-place pipes

101

ISO 11298-1:2018

Plastics piping systems for renovation of underground water supply networks — Part 1: General

102

ISO 11298-2:2018

Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes

103

ISO 11298-3:2018

Plastics piping systems for renovation of underground water supply networks — Part 3: Lining with close-fit pipes

104

ISO/DIS 11298-4

Plastics piping systems for renovation of underground water supply networks — Part 4: Lining with cured-in-place pipes

105

ISO 11299-1:2018

Plastics piping systems for renovation of underground gas supply networks — Part 1: General

106

ISO 11299-2:2018

Plastics piping systems for renovation of underground gas supply networks — Part 2: Lining with continuous pipes

107

ISO 11299-3:2018

Plastics piping systems for renovation of underground gas supply networks — Part 3: Lining with close-fit pipes

108

ISO/TS 11619:2014

Polyurethane tubing for use primarily in pneumatic installations — Dimensions and specification

109

ISO 11673:2005

Unplasticized poly(vinyl chloride) (PVC-U) pressure pipes — Determination of the fracture toughness properties

110

ISO 11922-1:2018

Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series

111

ISO 11922-2:1997

Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 2: Inch-based series

112

ISO 12091:1995

Structured-wall thermoplastics pipes — Oven test

113

ISO 12162:2009

Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient

114

ISO 12176-1:2017

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion

115

ISO 12176-2:2008

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion

116

ISO 12176-3:2011

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3: Operator's badge

117

ISO 12176-4:2003

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding

118

ISO/FDIS 12176-5

Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 5: Two-dimensional data coding of components and data exchange format for PE piping systems

119

ISO 12230:2012

Polybutene-1 (PB-1) pipes — Effect of time and temperature on the expected strength

120

ISO/TS 12512:2017

Glass reinforced thermosetting plastic (GRP) pipes — Determination of initial specific ring stiffness using segment test species cut from a pipe

121

ISO 13229:2010

Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value

122

ISO 13254:2010

Thermoplastics piping systems for non-pressure applications — Test method for watertightness

123

ISO 13255:2010

Thermoplastics piping systems for soil and waste discharge inside buildings — Test method for airtightness of joints

124

ISO 13257:2018

Thermoplastics piping systems for non-pressure applications — Test method for resistance to elevated temperature cycling

125

ISO 13259:2018

Thermoplastics piping systems for underground non-pressure applications — Test method for leaktightness of elastomeric sealing ring type joints

126

ISO 13260:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Test method for resistance to combined temperature cycling and external loading

127

ISO 13262:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics spirally-formed structured-wall pipes — Determination of the tensile strength of a seam

128

ISO 13263:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for impact strength

129

ISO 13264:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings

130

ISO 13265:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Joints for buried non-pressure applications — Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure

131

ISO 13266:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of resistance against surface and traffic loading

132

ISO 13267:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling resistance

133

ISO 13268:2010

Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness

134

ISO 13272:2011

Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) — Specifications for manholes and inspection chambers in traffic areas and underground installations

135

ISO 13477:2008

Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)

136

ISO 13478:2007

Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)

137

ISO 13479:2009

Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes

138

ISO 13480:1997

Polyethylene pipes — Resistance to slow crack growth — Cone test method

139

ISO 13760:1998

Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage

140

ISO 13761:2017

Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C

141

ISO 13844:2015

Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes — Test method for leaktightness under negative pressure, angular deflection and deformation

142

ISO 13845:2015

Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes — Test method for leaktightness under internal pressure and with angular deflection

143

ISO 13950:2007

Plastics pipes and fittings — Automatic recognition systems for electrofusion joints

144

ISO 13966:1998

Thermoplastics pipes and fittings — Nominal ring stiffnesses

145

ISO 13968:2008

Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility

146

ISO 14531-1:2002

Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 1: Pipes

147

ISO 14531-2:2004

Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 2: Fittings for heat-fusion jointing

148

ISO 14531-3:2010

Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 3: Fittings for mechanical jointing (including PE-X/metal transitions)

149

ISO 14531-4:2006

Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 4: System design and installation guidelines

150

ISO 15306:2003

Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the resistance to cyclic internal pressure

151

ISO 15874-1:2013

Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General

152

ISO 15874-2:2013

Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes

153

ISO 15874-5:2013

Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system

154

ISO 15875-2:2003

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes

155

ISO 15875-5:2003

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system

156

ISO/TS 15875-7:2018

Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 7: Guidance for the assessment of conformity

157

ISO 15876-2:2017

Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes

158

ISO 15876-5:2017

Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system

159

ISO/TS 15876-7:2018

Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 7: Guidance for the assessment of conformity

160

ISO 15877-1:2009

Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 1: General

161

ISO 15877-2:2009

Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 2: Pipes

162

ISO 15877-5:2009

Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 5: Fitness for purpose of the system

163

ISO/TS 15877-7:2018

Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 7: Guidance for the assessment of conformity

164

ISO 16241:2005

Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products (PENT)

165

ISO 16422:2014

Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Specifications

166

ISO/TS 16479:2012

Thermoplastics pipes for the conveyance of fluids — Determination of the slow cracking resistance of pipes and fittings using the Notched Ring Test (NRT)

167

ISO 16611:2017

Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests

168

ISO 16871:2003

Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering

169

ISO/TR 16913:1999

Plastics pipes and fittings — Definitions of types of test

170

ISO/TS 16943:2019

Thermoplastic pipes for the conveyance of fluids — Inspection of polyethylene electrofusion socket joints using phased array ultrasonic testing

171

ISO 17454:2006

Plastics piping systems — Multilayer pipes — Test method for the adhesion of the different layers using a pulling rig

172

ISO 17455:2005

Plastics piping systems — Multilayer pipes — Determination of the oxygen permeability of the barrier pipe

173

ISO 17456:2006

Plastics piping systems — Multilayer pipes — Determination of long-term strength

174

ISO 17484-1:2014

Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems

175

ISO 17484-2:2009

Plastics piping systems — Multilayer pipe systems for indoor gas installations — Part 2: Code of pratice

176

ISO 17778:2015

Plastics piping systems — Fittings, valves and ancillaries — Determination of gaseous flow rate/pressure drop relationships

177

ISO/TS 17902:2016

Wrapped electrofoaming joints for polyethylene (PE) piping systems with smooth outer wall for gravity drains and sewers

178

ISO/TR 18124:2006

Plastics piping systems — Multilayer M (metal) pipes — Test method for strength of the weld line in the metal layer and bonding between layers by use of a cone

179

ISO 18225:2012

Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems

180

ISO/TS 18226:2006

Plastics pipes and fittings — Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar)

181

ISO 18373-1:2007

Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of the processing temperature

182

ISO 18373-2:2008

Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 2: Measurement of the enthalpy of fusion of crystallites

183

ISO 18488:2015

Polyethylene (PE) materials for piping systems — Determination of Strain Hardening Modulus in relation to slow crack growth — Test method

184

ISO 18489:2015

Polyethylene (PE) materials for piping systems — Determination of resistance to slow crack growth under cyclic loading — Cracked Round Bar test method

185

ISO 18553:2002

Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds

186

ISO 18672-1:2009

Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints

187

ISO 18851:2015

Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test method to prove the structural design of fittings

188

ISO 19220:2004

Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Styrene copolymer blends (SAN + PVC)

189

ISO/TR 19480:2005

Polyethylene pipes and fittings for the supply of gaseous fuels or water — Training and assessment of fusion operators

190

ISO 19893:2011

Plastics piping systems — Thermoplastics pipes and fittings for hot and cold water — Test method for the resistance of mounted assemblies to temperature cycling

191

ISO 19899:2010

Plastics piping systems — Polyolefin pipes and mechanical fitting assemblies — Test method for the resistance to end load (AREL test)

192

ISO/TS 20656-1:2017

Plastics piping systems — General rules for structural design of glass-reinforced thermosetting plastics (GRP) pipes — Part 1: Buried pipes

193

ISO 21003-2:2008

Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes

194

ISO/TS 21003-7:2019

Multilayer piping systems for hot and cold water installations inside buildings — Part 7: Guidance for the assessment of conformity

195

ISO 21004:2006

Plastics piping systems — Multilayer pipes and their joints, based on thermoplastics, for water supply

196

ISO 21138-1:2007

Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Material specifications and performance criteria for pipes, fittings and system

197

ISO 21138-2:2007

Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2: Pipes and fittings with smooth external surface, Type A

198

ISO 21138-3:2007

Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B

199

ISO 21225-1:2018

Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 1: Replacement on the line by pipe bursting and pipe extraction

200

ISO 21225-2:2018

Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 2: Replacement off the line by horizontal directional drilling and impact moling

201

ISO 21307:2017

Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems

202

ISO 21751:2011

Plastics pipes and fittings — Decohesion test of electrofusion assemblies — Strip-bend test

203

ISO 22391-2:2009

Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes

204

ISO/TS 22499:2019

Thermoplastic pipes for the conveyance of fluids — Inspection of polyethylene butt fusion joints using phased array ultrasonic testing

205

ISO 23228:2011

Thermoplastics pipes for the conveyance of fluids — Determination of the stress-rupture resistance of moulding materials using plain strain grooved tensile (PSGT) specimens

206

ISO/TS 23818-1

Assessment of conformity of plastics piping systems for the rehabilitation of existing pipelines — Part 1: Polyethylene (PE) material

207

ISO/DIS 23856

Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

208

ISO 24033:2009

Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength

209

ISO 25780:2011

Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques

210

ISO/TS 26873:2010

Plastics pipes and fittings — Definition and construction procedures for reference lines

211

ISO/TR 27165:2012

Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes