KS M ISO 15109-2007

胶粘剂静载下胶接接头断裂时间的测定

Adhesives－Determination of the time to rupture of bonded joints   under static load

KS M ISO 15113-2007

橡胶.摩擦特性的测定

Rubber－Determination of frictional properties

KS M ISO 1513-2012

色漆和清漆.试验样品的检验和制备

Paints and varnishes－Examination and preparation of test   samples

KS M ISO 1514-2011

色漆和清漆试验用标准色盘

Paints and varnishes－Standard pannels for testing

KS M ISO 1516-2008

闪点/无闪点测定.闭杯平衡法

Determination of flash/no flash－Closed cup equilibrium method

KS M ISO 15166-1-2004

胶粘剂大块试样的制备方法第1部分：两部分系统

Adhesives－Methods of preparing bulk specimens－Part 1：Two-part systems

KS M ISO 15166-2-2004

胶粘剂大块试样的制备方法第2部分：高温固化单组分体系

Adhesives－Methods of preparing bulk specimens－Part 2：Elevated-temperature-curing   one-part systems

KS M ISO 15167-2003

石油产品中间馏分燃料颗粒含量测定实验室过滤法

Petroleum products－Determination of particulate content   of middle distillate fuels－Laboratory filtration   method

KS M ISO 15169-2005

石油和液体石油产品.用混合油罐测量系统测定立式油罐所含烃类的体积、密度和质量

Petroleum and liquid petroleum products -   Determination of volume, density and mass of the hydrocarbon content of   vertical cylindrical tanks by hybrid tank measurement systems

KS M ISO 1518-1-2012

色漆和清漆耐刮性的测定第1部分：恒载法

Paints and varnishes－Determination of scratch resistance－ Part 1：Constant-loading method

KS M ISO 15181-1-2013

色漆和清漆.防污漆中杀虫剂释放率的测定.第1部分：杀虫剂提取的一般方法

Paints and varnishes — Determination of release rate of   biocides from antifouling paints — Part 1: General   method for extraction of biocides

KS M ISO 15181-2-2013

色漆和清漆.防污漆中杀虫剂释放速率的测定.第2部分：萃取液中铜离子浓度的测定和释放速率的计算

Paints and varnishes — Determination of release rate of   biocides from antifouling paints — Part 2:   Determination of copper-ion concentration in the extract and calculation of   the release rate

KS M ISO 1518-2-2013

色漆和清漆耐刮性的测定第2部分：可变载荷法

Paints and varnishes－Determination of scratch resistance －Part 2: Variable-loading method

KS M ISO 15184-2013

色漆和清漆.使用铅笔测定薄膜硬度

Paints and varnishes ― Determination of film hardness by   pencil test

KS M ISO 1519-2012

色漆和清漆弯曲试验（圆柱芯轴）

Paints and varnishes－Bend test(cylindrical mandrel)

KS M ISO 1520-2012

色漆和清漆.压痕试验

Paints and varnishes－Cupping test

KS M ISO 1522-2008

色漆和清漆.摆杆阻尼试验

Paints and varnishes－Pendulum damping test

KS M ISO 1523-2008

闪点测定.闭杯平衡法

Determination of flash point－Closed cup equilibrium method

KS M ISO 15234-2017

色漆和清漆甲醛释放涂层和三聚氰胺泡沫试验小试验室中甲醛稳态浓度的测定

Paints and varnishes－Testing of formaldehyde-emitting   coatings and melamine foams－Determination of the   steady-state concentration of formaldehyde in a small test chamber

KS M ISO 1524-2013

色漆、清漆和油墨.研磨细度的测定

Paints, varnishes and printing ink — Determination of fineness of grind

KS M ISO 15270-2013

塑料.废水再循环和恢复指南

Plastics — Guidelines for recovery

KS M ISO 15306-2016

玻璃纤维增强热固塑料管耐循环内压的测定

Glass-reinforced thermosetting plastics   (GRP) pipes－Determination of the   resistance to cyclic internal pressure

KS M ISO 15310-2002

纤维增强塑料复合材料.用板捻法测定内剪模量

Fibre－reinforced plastic composites－Determination   of the in－plane shear modulus by the plate twist   method

KS M ISO 15318-2017

纸浆、纸和纸板7种特定多氯联苯（PCB）的测定

Pulp, paper and board－Determination of 7 specified   polychlorinated biphenyls(PCB)

KS M ISO 15320-2014

纸浆、纸和纸板.水提出物中五氯酚含量的测定

Pulp, paper and board — Determination of pentachlorophenol   in an aqueous extract

KS M ISO 15359-2008

纸和纸板.静态和动态摩擦系数的测定.水平面法

Paper and board－Determination of the static and   kinetic coefficients of friction－Horizontal plane   method

KS M ISO 15360-1-2017

再生纸浆粘性和塑料的测定第1部分：目视法

Recycled pulps－Estimation of Stickies and Plastics－Part 1：Visual method

KS M ISO 15360-2-2017

再生纸浆胶粘物和塑料的测定第2部分：图像分析法

Recycled pulps－Estimation of Stickies and Plastics－Part 2：Image analysis method

KS M ISO 15361-2017

纸浆湿、干零距抗张强度的测定

Pulps－Determination of zero-span tensile strength, wet or dry

KS M ISO 15380-2017

润滑剂、工业用油和相关产品(L类).系列H(液压系统).HETG,HEPG,HEES和HEP

Lubricants, industrial oils and related   products(class L)－Family   H(Hydraulic systems)－Specifications for categories   HETG, HEPG, HEES and HEPR

KS M ISO 15509-2010

粘合剂.工程塑料接头粘合强度的测定

Adhesives－Determination of the bond strength of   engineering-plastic joints

KS M ISO 15528-2015

色漆、清漆和相应的原料.取样

Paints, varnishes and raw materials for   paints and varnishes－Sampling

KS M ISO 15597-2003

石油及有关产品.氯和溴含量的测定.波长散射X射线荧光光谱测定法

Petroleum and related products－Determination of chlorine and bromine   content－Wavelength－dispersive   X－ray fluorescence spectrometry

KS M ISO 15605-2010

粘合剂.取样

Adhesives－Sampling

KS M ISO 15671-2007

橡胶和橡胶添加剂全硫含量的测定自动分析仪法

Rubber and rubber additives－Determination of total sulfur content   using an automatic analyser

KS M ISO 15672-2007

橡胶和橡胶添加剂用自动分析仪测定总氮含量

Rubber and rubber additives－Determination of total nitrogen   content using an automatic analyser

KS M ISO 15700-2002

皮革.色牢度试验.耐水斑点色牢度

Leather－Tests for colour fastness－Colour fastness   to water spotting

KS M ISO 15701-2017

皮革.色牢度试验.耐聚氯乙烯色牢度

Leather — Tests for colour fastness — Colour   fastness to migration into polymeric material

KS M ISO 15702-2007

皮革色牢度试验耐机洗色牢度

Leather－Tests for colour fastness－Colour fastness   to machine washing

KS M ISO 15703-2007

皮革色牢度试验耐温和洗涤色牢度

Leather－Tests for colour fastness－Colour fastness   to mild washing

KS M ISO 15710-2008

色漆和清漆缓冲氯化钠溶液交替浸除腐蚀试验方法

Paints and varnishes－Corrosion testing by alternate   immersion in and removal from a buffered sodium chloride solution

KS M ISO 15711-2016

色漆和清漆.曝露于海水中覆层的耐阴极解粘合作用的测定

Paints and varnishes－Determination of resistance to   cathodic disbonding of coatings exposed to sea water

KS M ISO 15715-2013

涂料和清漆用粘合剂.混浊度的测定

Binder for paints and varnishes — Determination for turbidity

KS M ISO 15741-2017

色漆和清漆.海上和近海的非腐蚀气体钢管内侧的减小摩擦涂层

Paints and varnishes－Friction-reduction coatings for the   interior of on-and offshore steel pipelines for non-corrosive gases

KS M ISO 15754-2016

纸和纸板Z向拉伸强度的测定

Paper and board－Determination of z-directional   tensile strength

KS M ISO 15755-2008

纸和纸板.杂质估算

Paper and board－Estimation of contraries

KS M ISO 15791-1-2014

塑料.塑料产品的中等规模燃烧试验的开发和使用.第1部分：一般指南

Plastics — Development and use of intermediate-scale fire tests   for plastics products — Part 1: General guidance

KS M ISO 15825-2017

橡胶配合剂炭黑圆盘离心光度法测定集料粒度分布

Rubber compounding ingredients－Carbon black－Determination   of aggregate size distribution by disc centrifuge photosedimentometry

KS M ISO 15850-2017

塑料拉伸疲劳裂纹扩展的测定线弹性断裂力学法

Plastics－Determination of tension-tension fatigue crack propagation－Linear elastic fracture mechanics(LEFM) approach

KS M ISO 15874-1-2016

冷热水塑料管道系统聚丙烯（PP）第1部分：总则

Plastics piping systems for hot and cold   water installations－Polypropylene   (PP)－Part 1：General

KS M ISO 15874-2-2016

冷热水塑料管道系统聚丙烯（PP）第2部分：管材

Plastics piping systems for hot and cold   water installations－Polypropylene   (PP)－Part 2：Pipes

KS M ISO 15874-3-2017

冷热水塑料管道系统聚丙烯（PP）第3部分：管件

Plastics piping systems for hot and cold   water installations－Polypropylene(PP)－Part 3：Fittings

KS M ISO 15874-5-2016

冷热水塑料管道系统聚丙烯（PP）第5部分：系统适用性

Plastics piping systems for hot and cold   water installations－Polypropylene   (PP)－Part 5：Fitness for   purpose of the system

KS M ISO 15875-1-2008

冷热水塑料管道系统交联聚乙烯（PE-X）第1部分：总则

Plastics piping systems for hot and cold   water installations－Crosslinked   polyethylene(PE-X)－Part 1：General

KS M ISO 15875-3-2008

冷热水塑料管道系统交联聚乙烯（PE-X）第3部分：管件

Plastics piping systems for hot and cold   water installations－Crosslinked   polyethylene(PE-X)－Part 3：Fittings

KS M ISO 15876-1-2008

冷热水塑料管道系统聚丁烯（PB）第1部分：总则

Plastics piping systems for hot and cold   water installations－Polybutylene(PB)－Part 1：General

KS M ISO 15876-2-2016

冷热水用塑料管道系统聚丁烯第2部分：管道

Plastics piping systems for hot and cold   water installations ㅡ Polybutylene (PB) ㅡ Part 2: Pipes

KS M ISO 15876-3-2013

冷热水塑料管道系统聚丁烯（PB）第3部分：管件

Plastics piping systems for hot and cold   water installations－Polybutylene(PB)－Part 3：Fittings

KS M ISO 15876-5-2013

冷热水塑料管道系统聚丁烯（PB）第5部分：系统适用性

Plastics piping systems for hot and cold   water installations－Polybutylene(PB)－Part 5：Fitness for purpose of the system

KS M ISO 15877-1-2008

冷热水用塑料管道系统氯化聚氯乙烯（PVC-C）第1部分：总则

Plastics piping systems for hot and cold   water installations－Chlorinated   poly(vinyl chloride)(PVC-C)－Part 1：General

KS M ISO 15880-2017

色漆、清漆和粘合剂水基涂层材料和粘合剂meq值的测定

Paints, varnishes and binders－Determination of MEQ value of   water-based coating materials and binders

KS M ISO 15906-2016

铝阳极用碳素材料透气性的测定

Carbonaceous materials for the production   of aluminium－Baked anodes－Determination of the air permeability

KS M ISO 15987-2017

塑料.薄膜和薄板.双轴取向聚酰胺（尼龙）薄膜

Plastics - Film and sheeting - Biaxially   oriented polyamide(nylon) films

KS M ISO 15988-2017

塑料.薄膜和薄板.双轴取向聚（乙烯基对苯二甲酸酯）（PET）薄膜

Plastics - Film and sheeting - Biaxially   oriented poly(ethyleneterephthalate) (PET) films

KS M ISO 16010-2007

弹性密封件气体燃料和烃类流体管道和配件用密封件的材料要求

Elastomeric seals－Material requirements for seals used   in pipes and fittings carrying gaseous fuels and hydrocarbon fluids

KS M ISO 16012-2014

塑料.试样线性尺寸的测定

Plastics — Determination of linear dimensions of test specimens

KS M ISO 16037-2008

临床试验用橡胶避孕套物理性能的测定

Rubber condoms for clinical trials－Measurement of physical properties

KS M ISO 16038-2008

橡胶避孕套.天然橡胶乳胶避孕套质量管理中使用KS M ISO 4074的指南

Rubber condoms－Guidance on the use of KS M ISO 4074   in the quality management of natural rubber latex condoms

KS M ISO 16053-2016

涂料和清漆.外部木材用涂层材料和涂覆系统.自然老化试验

Paints and varnishes－Coating materials and coating systems   for exterior wood－Natural weathering test

KS M ISO 16065-1-2016

纸浆自动光学分析法测定纤维长度第1部分：偏振光法

Pulps－Determination of fibre length by automated optical analysis－Part 1：Polarized light method

KS M ISO 16065-2-2016

纸浆自动光学分析法测定纤维长度第2部分：无偏振光法

Pulps－Determination of fiber length by automated optical analysis－Part 2：Unpolarized light method

KS M ISO 161-1

流体输送用热塑性塑料管材.公称外径和公称压力.第1部分:公制系列

Thermoplastics pipes for the conveyance of   fluids－Nominal outside   diameters and nominal pressures－Part 1：Metric series

KS M ISO 16152-2006

塑料聚丙烯中二甲苯可溶物的测定

Plastics－Determination of xylene-soluble matter in polypropylene

KS M ISO 1617-2003

主要用于铝生产的氧化铝.钠含量的测定.火焰发射分光光度法

Aluminium oxide primarily used for the   production of aluminium－Determination   of sodium content－Flame emission spectrophotometric   method

KS M ISO 16212-2010

化妆品微生物学酵母和霉菌的计数

Cosmetics－Microbiology－Enumeration of   yeast and mould

KS M ISO 1622-1-2013

塑料.聚苯乙烯（PS）模塑和挤塑材料.第1部分：命名系统和基本规范

PLASTIC — POLYSTYRENE(PS) MOULDING AND EXTRUSION MATERIALS — PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS

KS M ISO 1622-2-2008

塑料－聚苯乙烯（PS）模塑和挤塑材料－第2部分：试样制备和性能测定

Plastics－Polystyrene(PS) moulding and extrusion materials－Part 2：Preparation of test specimens and   determination of properties

KS M ISO 16276-1-2013

防护涂料体系对钢结构的腐蚀防护涂层粘附/粘聚力（断裂强度）的评定和验收标准第1部分：拉拔试验

Corrosion protection of steel structures by   protective paint systems ㅡ Assessment of, and   acceptance criteria for, the adhesion/cohesion (fracture strength) of a   coating ㅡ Part 1: Pull-off testing

KS M ISO 16276-2-2013

防护涂料体系对钢结构的腐蚀防护涂层的粘附/粘聚力（断裂强度）的评定和验收标准第2部分：横切试验和X切试验

Corrosion protection of steel structures by   protective paint systems ㅡ Assessment of, and   acceptance criteria for, the adhesion/cohesion (fracture strength) of a   coating ㅡ Part 2: Cross-cut testing and X-cut   testing

KS M ISO 1628-1-2012

塑料.用毛细管粘度计测定稀释溶液中聚合物的粘度.第1部分：一般原理

Plastics－Determination of the viscosity of polymers in dilute solution   using capillary viscometers－Part 1：General principles

KS M ISO 1628-2-2010

塑料聚合物稀溶液粘度的测定毛细管粘度计第2部分：聚氯乙烯树脂

Plastics－Determination of the viscosity of polymers in dilute solution   using capillary viscometers－Part 2：Poly(vinyl chloride) resins

KS M ISO 1629-2017

橡胶和胶乳.术语

Rubbers and latices－Nomenclature

KS M ISO 16392-2015

轮胎－电阻－在试验台上测量轮胎电阻的试验方法

Tyres－Electrical resistance－Test method for   measuring electrical resistance of tyres on a test rig

KS M ISO 16474-1-2016

色漆和清漆实验室光源曝露试验方法第1部分：通用指南

Paints and varnishes ㅡ Methods of exposure to laboratory light sources ㅡ Part 1: General guidance

KS M ISO 16474-2-2016

色漆和清漆实验室光源曝露试验方法第1部分：通用指南

Paints and varnishes ㅡ Methods of exposure to laboratory light sources ㅡ Part 1: General guidance

KS M ISO 16474-3-2017

色漆和清漆实验室光源曝露试验方法第3部分：荧光紫外灯

Paints and varnishes ㅡ Methods of exposure to laboratory light sources ㅡ Part 3: Fluorescent UV lamps

KS M ISO 16474-4-2016

色漆和清漆实验室光源曝露试验方法第4部分：明火碳弧灯

Paints and varnishes ㅡ Methods of exposure to laboratory light sources ㅡ Part 4: Open-flame carbon-arc lamp

KS M ISO 1652-2015

橡胶胶乳.用布洛氏布洛克菲尔德试验方法测定表观粘度

Rubber latex－Determination of viscosity

KS M ISO 16532-1-2009

纸和纸板耐油脂性的测定第1部分：渗透性试验

Paper and board－Determination of grease resistance－Part 1：Permeability test

KS M ISO 16532-2-2009

纸和纸板耐油性的测定第2部分：表面排斥试验

Paper and board－Determination of grease resistance－Part 2：Surface repellency test

KS M ISO 1656-2015

天然生胶和天然胶乳.氮含量的测定

Rubber, raw natural, and rubber latex,   natural－Determination of   nitrogen content

KS M ISO 16564-2007

天然橡胶.由尺寸排除色谱法测定平均分子质量和分子质量分布(SEC)

Rubber, raw natural－Determination of average molecular   mass and molecular－mass distribution by size   exclusion chromatography(SEC)

KS M ISO 16565-2017

橡胶.乙烯-丙烯-二烯三共聚物中5-亚乙基-降冰片烯(ENB)或二聚环戊二烯(DCPD)的测定

Rubber — Determination of 5-ethylidenenorbornene(ENB) or   dicyclopentadiene(DCPD) in ethylene-propylene-diene(EPDM) terpolymers

KS M ISO 1657-2012

生橡胶和胶乳铁含量的测定1，10-二氮杂菲光度法

Rubber, raw and rubber latex－Determination of iron content－1,10-Phenanthroline photometric method

KS M ISO 1658-2010

天然橡胶(NR).评估程序

Natural rubber(NR)－Evaluation procedure

KS M ISO 16591-2012

石油产品硫含量测定氧化微库仑法

Petroleum products－Determination of sulfur content－ Oxidative microcoulometry method

KS M ISO 1663-2013

硬质泡沫塑料.水蒸气传输特性的测定

Rigid cellular plastics — Determination of water vapour   transmission properties

KS M ISO 1675-2007

塑料液态树脂密度的测定比重瓶法

Plastics－Liquid resins－Determination of density by   the pyknometer method

KS M ISO 16773-1-2013

色漆和清漆高阻抗涂层试样上的电化学阻抗光谱法（EIS）第1部分：术语和定义

Paints and varnishes ㅡ Electrochemical impedance spectroscopy (EIS) on   high-impedance coated specimens ㅡ   Part 1: Terms and definitions

KS M ISO 16773-2-2013

色漆和清漆高阻抗涂层试样的电化学阻抗谱（EIS）第2部分：术语和定义

Paints and varnishes ㅡ Electrochemical impedance spectroscopy (EIS) on   high-impedance coated specimens ㅡ   Part 2: Terms and definitions

KS M ISO 16773-3-2013

色漆和清漆高阻抗涂层样品的电化学阻抗光谱法（EIS）第3部分：假细胞数据的处理和分析

Paints and varnishes ㅡ Electrochemical impedance spectroscopy (EIS) on   high-impedance coated specimens ㅡ   Part 3: Processing and analysis of data from dummy cells

KS M ISO 16773-4-2013

色漆和清漆高阻抗涂层试样的电化学阻抗光谱法（EIS）第4部分：聚合物涂层试样的光谱示例

Paints and varnishes ㅡ Electrochemical impedance spectroscopy (EIS) on   high-impedance coated specimens ㅡ   Part 4: Examples of spectra of polymer-coated specimens

KS M ISO 16805-2011

色漆和清漆用粘合剂.玻璃化转变温度的测定

Binders for paints and varnishes－Determination of glass transition   temperature

KS M ISO 1686-2017

工业用硅酸钠和硅酸钾.取样和试验方法.总则

Sodium and potassium silicates for   industrial use —   Samples and methods of test — General

KS M ISO 16862-2011

色漆和清漆耐下垂性的评定

Paints and varnishes－Evaluation of sag resistance

KS M ISO 16869-2014

塑料.塑料配方中杀菌剂化合物有效性的评定

Plastics — Assessment of the effectiveness of fungistatic   compounds in plastics formulations

KS M ISO 1689-2017

工业用硅酸钠和硅酸钾.二氧化硅/氧化钠或二氧化硅/氧化钾比率的计算

Sodium and potassium silicates for   industrial use —   Calculation of the ratio: silicon dioxide/sodium oxide or silicon   dioxide/potassium oxide

KS M ISO 1690-2017

工业用硅酸钠和硅酸钾.二氧化硅含量的测定.不溶解物重量法

Sodium and potassium silicates for   industrial use —   Determination of silica content — Gravimetric method   by insolubilization

KS M ISO 1691-2017

工业用硅酸钠和硅酸钾.碳酸盐含量的测定.气体容积法

Sodium and potassium silicates for   industrial use —   Determination of carbonates content — Gas-volumetric   method

KS M ISO 1692-2017

工业用硅酸钠和硅酸钾.总碱度的测定.滴定法

Sodium and potassium silicates for   industrial use —   Determination of total alkalinity — Titrimetric   method

KS M ISO 16925-2018

色漆和清漆.涂层耐高压水喷射的测定

Paints and varnishes - Determination of the   resistance of coatings to pressure water-jetting

KS M ISO 16927-2018

色漆和清漆.涂层的可复涂性和可复涂性的测定

Paints and varnishes - Determination of the   overcoatability and recoatability of a coating

KS M ISO 16929-2015

塑料中试确定堆肥条件下塑料材料崩解程度的测定

Plastics－Determination of the degree of disintegration of plastic materials   under defined composting conditions in a pilot-scale test

KS M ISO 1693-2017

天然和人造冰晶石.氟含量的测定.威拉德-温特尔的改进法

Cryolite, natural and artificial — Determination of fluorine content — Modified Willard — Winter method

KS M ISO 16992-2015

轿车轮胎－备用单元替换设备（SUSE）

Passenger car tyres－Spare unit substitutive   equipment(SUSE)

KS M ISO 17052-2012

生橡胶.用毛细管气相色谱法测定残余单体和其它挥发性低分子质量化合物.热解吸（动态顶空）法

Rubber, raw－Determination of residual monomers and other volatile   low-molecular-mass compounds by capillary gas chromatography－ Thermal desorption(dynamic headspace) method

KS M ISO 17070-2017

皮革.化学试验.四氯苯酚、三氯苯酚、二氯苯酚、一氯苯酚异构体和五氯酚含量的测定

Leather — Chemical tests — Determination of   tetrachlorophenol-, trichlorophenol-, dichlorophenol-,   monochlorophenol-isomers and pentachlorophenol content

KS M ISO 17071-2007

皮革物理力学试验起雾性能的测定

Leather－Physical and mechanical tests－Determination   of fogging characteristics

KS M ISO 17074-2007

皮革物理力学试验抗水平火焰蔓延性的测定

Leather－Physical and mechanical tests－Determination   of resistance to horizontal spread of flame

KS M ISO 17075-2008

皮革化学试验铬含量的测定

Leather－Chemical tests－Determination of   chromium(VI) content

KS M ISO 17076-2007

皮革物理力学试验汽车革耐磨性的测定

Leather－Physical and mechanical tests－Determination   of abrasion resistance of automotive leather

KS M ISO 17132-2013

色漆和清漆T形弯曲试验

Paints and varnishes ㅡ T-bend test

KS M ISO 17186-2013

皮革_物理力学试验_表面涂层厚度的测定

Leather ㅡ   Physical and mechanical tests ㅡ   Determination of surface coating thickness

KS M ISO 17212-2013

结构胶粘剂.粘结前金属和塑料的表面准备指南

Structural adhesives -- Guidelines for the   surface preparation of metals and plastics prior to adhesive bonding

KS M ISO 172-2002

塑料.酚-测模塑件.游离氨的检验

Plastics－Phenol-formaldehyde mouldings－Determination   of free ammonia

KS M ISO 17226-1-2014

皮革甲醛含量的化学测定第1部分：高效液相色谱法

Leather — Chemical determination of formaldehyde content — Part 1: Method using high performance liquid chromatography

KS M ISO 17226-2-2014

皮革甲醛含量的化学测定第2部分：比色分析法

Leather — Chemical determination of formaldehyde content — Part 2: Method using colorimetric analysis

KS M ISO 17226-3-2014

皮革.甲醛含量的化学测定.第3部分：皮革甲醛排放量的测定

Leather — Chemical determination of formaldehyde content — Part 3 : Determination of formaldehyde emissions from leather

KS M ISO 17227-2008

皮革物理力学试验皮革耐干热性的测定

Leather－Physical and mchanical tests－Determination   of dry heat resistance of leather

KS M ISO 17228-2016

皮革.色牢度试验.加速老化中的颜色变化

Leather－Tests for colour fastness－Change in colour   with accelerated ageing

KS M ISO 17229-2008

皮革物理力学性能试验水蒸气吸收率的测定

Leather－Physical and mchanical tests－Determination   of water vapour absorption

KS M ISO 17230-2007

皮革物理力学试验渗水压力的测定

Leather－Physical and mechanical tests－Determination   of water penetration pressure

KS M ISO 17231-2007

皮革物理力学试验服装革拒水性的测定

Leather－Physical and mechanical tests－Determination   of water repellency of garment leather

KS M ISO 17232-2007

皮革物理力学试验专利革耐热性的测定

Leather－Physical and mechanical tests－Determination   of heat resistance of patent leather

KS M ISO 17233-2008

皮革物理力学性能试验表面涂层冷裂温度的测定

Leather－Physical and mchanical tests－Determination   of cold crack temperature of surface coatings

KS M ISO 17234-1-2014

皮革染色革中某些偶氮着色剂测定的化学试验第1部分：偶氮着色剂中某些芳香胺的测定

Leather ─ Chemical tests for the determination of certain azo colorants in   dyed leathers ─ Part 1: Determination of certain   aromatic amines derived from azo colorants

KS M ISO 17234-2-2014

皮革.染色皮革中某些偶氮着色剂测定的化学试验.第2部分：4-氨基偶氮苯的测定

Leather — Chemical tests for the determination of certain azo colorants in   dyed leathers — Part 2: Determination of   4-aminoazobenzene

KS M ISO 17235-2013

皮革物理力学试验柔软度的测定

Leather ㅡ   Physical and mechanical tests ㅡ   Determination of softness

KS M ISO 17236-2008

皮革物理力学性能试验拉伸永久变形的测定

Leather－Physical and mchanical tests－Determination   of extension set

KS M ISO 17249-2016

抗链锯切割安全鞋

Safety footwear with resistance to chain   saw cutting

KS M ISO 17269-2007

轿车轮胎滚动周长测量方法新轮胎

Passenger car tyres－Methods for measuring rolling   circumference－Loaded new tyres

KS M ISO 17281-2007

塑料中高加载速率（1 m/s）下断裂韧性（gic和kic）的测定

Plastics－Determination of fracture toughness (GIC and KIC) at moderately   high loading rates(1 m/s)

KS M ISO 17422-2010

塑料.环境方面.标准中环境方面的一般指南

Plastics－Environmental aspects－General guidelines   for their inclusion in standards

KS M ISO 17463-2018

涂料和清漆.用加速循环电化学技术测定有机涂层防腐性能的指南

Paints and varnishes - Guidelines for the   determination of anticorrosive properties of organic coatings by accelerated   cyclic electrochemical technique

KS M ISO 17499-2016

铝生产用碳素材料等效温度表示的焙烤度的测定

Carbonaceous materials used in the   production of aluminium－Determination   of baking level expressed by equivalent temperature

KS M ISO 17500-2016

原铝生产用氧化铝磨损指数的测定

Aluminium oxide used for the production of   primary aluminium－Determination   of attrition index

KS M ISO 1750-2003

农药和其他农用化学品.通用名称

Pesticides and other agrochemicals－Common names

KS M ISO 175-2016

塑料浸入液体化学药品影响测定的试验方法

Plastics－Methods of test for the determination of the effects of immersion   in liquid chemicals

KS M ISO 17531-2002

摄影.冲卷药液.4-(N-乙基-N-2甲基磺酰氨乙基)2-甲苯二胺倍半硫酸盐水化合物的规范

Photography－Processing chemicals－Specifications   for 4－(N－ethyl－N－2－methanesulfonylaminoethyl)－2－methylphenylenediamine sesquisulfate   monohydrate

KS M ISO 17541-2016

塑料划痕损伤和划痕可见度的定量评定

Plastics － Quantitative evaluation of scratch-induced damage and   scratch visibility

KS M ISO 17555-2012

塑料薄膜和片材双轴取向聚丙烯薄膜

Plastics－Film and sheeting－ Biaxially oriented   polypropylene(PP) films

KS M ISO 17556-2015

塑料.通过呼吸计中需氧量的测量或放出的二氧化碳量的测量测定土壤中的最大需氧生物降解能力

Plastics－Determination of the ultimate aerobic biodegradability in soil by   measuring the oxygen demand in a respirometer or the amount of carbon dioxide   evolved

KS M ISO 17557-2017

塑料.薄膜和薄板.铸造聚丙烯（PP）薄膜

Plastics - Film and sheeting - Cast   polypropylene(PP) films

KS M ISO 17564-2012

腈橡胶.用碘值测定氢化的腈橡胶（HNBR）中的剩余非饱和物

Nitrile rubber－Determination of residual   unsaturation of hydrogenated nitrile rubber(HNBR) by iodine value

KS M ISO 1762-2004

纸浆、纸板和纸.在525℃燃烧残余物的测定

Paper, board and pulp－Determination of residue(ash) on   ignition at 525℃

KS M ISO 17693-2005

鞋靴.鞋帮试验方法.耐磨损性

Footwear－Test methods for uppers－Resistance to   damage on lasting

KS M ISO 17694-2004

鞋靴.鞋帮和鞋衬的试验方法.抗弯性

Footwear－Test methods for uppers and lining－Flex   resistance

KS M ISO 17695-2005

鞋靴.鞋帮试验方法.变形性

Footwear－Test methods for uppers－Deformability

KS M ISO 17696-2005

鞋靴.鞋帮、鞋衬和鞋底试验方法.抗扯裂强度

Footwear－Test methods for uppers, linings and insocks－Tear strength

KS M ISO 17697-2004

鞋靴.鞋帮、鞋衬和内垫的试验方法.缝口强度

Footwear－Test methods for uppers, lining and insocks－Seam strength

KS M ISO 17698-2004

鞋靴.鞋帮的试验方法.耐剥离性

Footwear－Test methods for uppers－Delamination   resistance

KS M ISO 17699-2004

鞋靴.鞋帮及鞋衬的试验方法.水蒸气的渗透性和吸收性

Footwear－Test methods for uppers and lining－Water   vapour permeability and absorption

KS M ISO 17700-2005

鞋靴.鞋帮、鞋衬和鞋内衬试验方法.耐摩擦色牢度

Footwear－Test methods for uppers, linings and insocks－Colour fastness to rubbing

KS M ISO 17701-2004

鞋靴.鞋帮、鞋衬和内垫的试验方法.色移

Footwear－Test methods for uppers, lining and insocks－Colour migration

KS M ISO 17702-2004

鞋靴.鞋帮的试验方法.防水性

Footwear－Test methods for uppers－Water resistance

KS M ISO 17703-2004

鞋靴.鞋帮的试验方法.高温特性

Footwear－Test methods for uppers－High temperature   behaviour

KS M ISO 17704-2005

鞋靴.鞋帮、鞋衬和鞋内衬试验方法.耐磨性

Footwear－Test methods for uppers, linings and insocks－Abrasion resistance

KS M ISO 17705-2004

鞋靴.鞋帮、鞋衬和内垫的试验方法.隔热性

Footwear－Test methods for uppers, lining and insocks－Thermal insulation

KS M ISO 17706-2004

鞋靴.鞋帮的试验方法.抗拉强度和伸长度

Footwear－Test methods for uppers－Tensile strength   and elongation

KS M ISO 17707-2006

鞋靴.外底的试验方法.抗弯性

Footwear－Test methods for outsoles－Flex resistance

KS M ISO 17708-2004

鞋靴.整鞋的试验方法.外鞋底的附着力

Footwear－Test methods for whole shoe－Upper sole   adhesion

KS M ISO 17709-2005

鞋靴.样品和试件的调节时间、取样位置和制备

Footwear－Sampling location, preparation and duration of conditioning of   samples and test pieces

KS M ISO 177-2003

塑料.增塑剂分散性的测定

Plastics－Determination of migration of plasticizers

KS M ISO 17812-2009

纸、纸板和纸浆总镁、总钙、总锰、总铁和总铜的测定

paper, board and pulps－Determination of total magnesium,   total calcium, total manganese, total iron and total copper

KS M ISO 178-2012

塑料弯曲性能试验方法

Plastics－Determination of flexural properties

KS M ISO 17855-1-2017

塑料聚乙烯（PE）模塑和挤塑材料第1部分：命名体系和基本规范

Plastics ㅡ   Polyethylene (PE) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 17855-2-2017

塑料聚乙烯（PE）模塑和挤塑材料第2部分：试样制备和性能测定

Plastics ㅡ   Polyethylene (PE) moulding and extrusion materials ㅡ Part 2: Preparation of test specimens and   determination of properties

KS M ISO 17872-2013

色漆和清漆腐蚀试验用金属板涂层上划痕引入指南

Paints and varnishes ㅡ Guidelines for the introduction of scribe marks   through coatings on metallic panels for corrosion testing

KS M ISO 17895-2016

色漆和清漆低VOC乳胶漆挥发性有机化合物含量的测定（罐内VOC）

Paints and varnishes－Determination of the volatile organic   compound content of low-VOC emulsion paints(in-can VOC)

KS M ISO 179-1

塑料夏比冲击性能的测定第1部分：非仪器冲击试验

Plastics－Determination of Charpy impact properties－Part   1：Non-instrumented impact test

KS M ISO 179-2

塑料夏比冲击性能的测定第2部分：仪器冲击试验

Plastics－Determination of Charpy impact properties－Part   2：Instrumented impact test

KS M ISO 1795-2017

天然生胶和合成生胶取样及制备方法

Rubber, raw natural and raw synthetic－Sampling and further preparative   procedures

KS M ISO 17958-2014

纸和纸板.断裂韧性的测定.恒速拉伸法（1.7mm/s）

Paper and board — Determination of fracture toughness — Constant rate of elongation method(1.7 mm/s)

KS M ISO 1798-2012

软质泡沫聚合材料拉伸强度和断裂伸长的测定

Flexible cellular polymeric materials－Determination of tensile strength and   elongation at break

KS M ISO 180-2012

硬质塑料悬臂梁冲击试验方法

Plastics－Determination of Izod impact strength

KS M ISO 1802-2009

浓缩天然胶乳.硼酸含量的测定

Natural rubber latex concentrate－Determination of boric acid content

KS M ISO 18132-1-2012

冷冻轻烃和非石油基液化气体燃料自动液位计通用要求第1部分：船载和浮式储存液化天然气用自动液位计

Refrigerated light hydrocarbon and   non-petroleum based liquefied gaseous fuels－General requirements for automatic tank gauges－Part 1：Automatic tank gauges for liquefied   natural gas on board marine carriers and floating storage

KS M ISO 18132-2-2010

冷冻轻烃流体自动液位计的一般要求第2部分：冷冻式岸边罐的液位计

Refrigerated light hydrocarbon fluids－General requirements for automatic   level gauges－Part 2：Gauges in   refrigerated-type shore tanks

KS M ISO 18132-3-2012

冷冻碳氢化合物和非石油基液化气体燃料自动液位计的一般要求第3部分：船载和浮式储存用液化石油气和化学气的自动液位计

Refrigerated hydrocarbon and non-petroleum   based liquefied gaseous fuels－General requirements for automatic tank gauges－ Part 3：Automatic tank gauges for   liquefied petroleum and chemical gases on board marine carriers and floating   storage

KS M ISO 18152-2008

土壤质量.土壤样品长期和短期贮存指南

Soil quality－Guidance on long and short term storage of soil   samples

KS M ISO 18164-2016

轿车、卡车、公共汽车和摩托车轮胎滚动阻力的测量方法

Passenger car, truck, bus and motorcycle   tyres－Methods of measuring   rolling resistance

KS M ISO 1817-2015

硫化橡胶.液体作用的测定

Rubber, vulcanized－Determination of the effect of   liquids

KS M ISO 1823-1-2008

橡胶软管和软管组件.第1部分:近海排吸油用软管.规范

Rubber hoses and hose assemblies－Part 1：On-shore   oil suction and discharge－Specification

KS M ISO 1825-2012

飞机地面加油和放油用橡胶软管和软管组件规范

Rubber hoses and hose assemblies for   aircraft ground fuelling and defuelling－Specification

KS M ISO 1827-2014

硫化或热塑性橡胶.剪切模量或与硬板粘合强度测定.四倍剪切法

Rubber, vulcanized or thermoplastic — Determination of modulus in shear or   adhesion to rigid plates — Quadruple shear method

KS M ISO 18415-2014

化妆品.微生物学.特定和非特定微生物的检测

Cosmetics — Microbiology — Detection of   specified and non-specified microorganisms

KS M ISO 18416-2014

化妆品.微生物学.白色念珠菌的检测

Cosmetics — Microbiology — Detection of   Candida albicans

KS M ISO 18454-2007

鞋靴.鞋靴和鞋靴部件的调节和试验用标准大气

Footwear－Standard atmospheres for conditioning and testing of footwear and   components for footwear

KS M ISO 18515-2016

铝生产用碳素材料阴极块和阳极焙烧抗压强度的测定

Carbonaceous materials for the production   of aluminium－Cathode blocks and   baked anodes－Determination of compressive strength

KS M ISO 18517-2017

硫化橡胶或热塑性橡胶.硬度试验.介绍和指南

Rubber, vulcanized or thermoplastic — Hardness testing — Introduction and guide

KS M ISO 1853-2008

硫化或热塑性导电和耗散橡胶电阻率的测定

Conducting and dissipative rubbers,   vulcanized or thermoplastic－Measurement of resistivity

KS M ISO 18553-2015

在聚烯烃管、配件和化合物中色料或炭黑分散体的等级评定方法

Method for the assessment of the degree of   pigment or carbon black dispersion in polyolefin pipes, fitting and compounds

KS M ISO 1856-2007

软质泡沫聚合材料压缩永久变形的测定

Flexible cellular polymeric materials－Determination of compression set

KS M ISO 186-2004

纸和纸板.测定平均质量取样

Paper and board－Sampling to determine average quality

KS M ISO 187-2016

纸浆、纸和纸板.温湿处理和试验的标准大气及其控制程序与试样温湿处理的步骤

Paper, board and pulps — Standard atmosphere for conditioning   and testing and procedure for monitoring the atmosphere and conditioning of   samples

KS M ISO 1874-1-2013

塑料.聚酰胺（PA）模塑和挤塑材料.第1部分：名称与符号

PLASTICS — POLYAMIDE(PA) MOULDING AND EXTRUSION MATERIALS — PART 1: DESIGNATION

KS M ISO 1874-2-2013

塑料.聚酰胺（PA）模塑和挤塑材料.第2部分：试样制备和性能测定

PLASTIC — POLYAMIDE(PA) MOULDING AND EXTRUSION MATERIALS — PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF   PROPERTIES

KS M ISO 18752-2014

橡胶软管和软管组件.液压设备用钢丝或纺织增强单压力型.规范

Rubber hoses and hose assemblies — Wire- or textilereinforced   single-pressure types for hydraulic applications —   Specification

KS M ISO 188-2014

硫化或热塑性橡胶.加速老化或耐热性试验

Rubber, vulcanized or thermoplastic — Accelerated ageing and heat   resistance tests

KS M ISO 18872-2014

塑料.高应变率下拉伸性能的测定

Plastics — Determination of tensile properties at high strain   rates

KS M ISO 18895-2008

鞋类柄部试验方法抗疲劳性能

Footwear－Test methods for shanks－Fatigue resistance

KS M ISO 18896-2008

鞋靴柄部试验方法纵向刚度

Footwear－Test methods for shanks－Longitudinal   stiffness

KS M ISO 18898-2015

橡胶硬度计的校准与检定

Rubber－Calibration and verification of hardness testers

KS M ISO 18899-2017

橡胶试验设备校准指南

Rubber－Guide to the calibration of test equipment

KS M ISO 19003-2015

橡胶和橡胶制品统计在物理试验中的应用指南

Rubber and rubber products－Guidance on the application of   statistics to physical testing

KS M ISO 19004-2007

橡胶和橡胶产品.试验方法的灵敏度测定

Rubber and rubber products－Determination of the sensitivity of   test methods

KS M ISO 19013-1-2007

内燃机燃油管路用橡胶软管规范第1部分：柴油

Rubber hoses and tubing for fuel cirecuits   for internal combustion engines－Specification－Part 1：Diesel fuels

KS M ISO 19013-2-2017

内燃机燃料回路用橡胶软管和管.规范.第2部分：汽油燃料

Rubber hoses and tubing for fuel circuits   for internal combustion engines — Specification — Part 2: Gasoline fuels

KS M ISO 19062-1-2017

塑料丙烯腈-丁二烯-苯乙烯（ABS）模塑和挤塑材料第1部分：命名系统和基本规范

Plastics ㅡ   Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 19063-1-2017

塑料_耐冲击聚苯乙烯（PS-I）模塑和挤塑材料_第1部分：命名系统和基本规范

Plastics ㅡ   Impact-resistant polystyrene (PS-I) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 19064-1-2017

塑料_苯乙烯/丙烯腈（SAN）模塑和挤塑材料_第1部分：命名系统和基本规范

Plastics ㅡ   Styrene/acrylonitrile (SAN) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 19066-1-2017

塑料甲基丙烯酸甲酯-丙烯腈-丁二烯-苯乙烯（MABS）模塑和挤塑材料第1部分：命名体系和基本规范

Plastics ㅡ   Methyl methacrylate-acrylonitrile- butadiene-styrene (MABS) moulding and   extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 19069-1-2017

塑料聚丙烯（PP）模塑和挤塑材料第1部分：命名体系和基本规范

Plastics ㅡ   Polypropylene (PP) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 19069-2-2017

塑料聚丙烯（PP）模塑和挤塑材料第2部分：试样制备和性能测定

Plastics ㅡ   Polypropylene (PP) moulding and extrusion materials ㅡ Part 2: Preparation of test specimens and   determination of properties

KS M ISO 19212-2014

胶粘剂.剪切强度温度依赖性的测定

Adhesives — Determination of temperature dependence of shear   strength

KS M ISO 1922-2013

泡沫塑料.硬质材料的剪切强度的测定

Rigid cellular plastics — Determination of shear strength

KS M ISO 1923-2010

泡沫塑料和橡胶.线性尺寸的测定

Cellular plastics and rubbers－Determination of linear dimensions

KS M ISO 1924-2-2009

纸和纸板拉伸性能的测定第2部分：恒速拉伸法（20 mm/min）

Paper and board－Determination of tensile properties－Part 2：Constant rate of elongation   method(20 mm/min)

KS M ISO 1924-3-2016

纸和纸板拉伸性能的测定第3部分：恒速拉伸法（100 mm/min）

Paper and board－Determination of tensile properties－Part 3：Constant rate of elongation method(100   mm/min)

KS M ISO 19252-2014

塑料.划痕性能的测定

Plastics — Determination of scratch properties

KS M ISO 1926-2013

硬质泡沫塑料.拉伸性能的测定

Rigid cellular plastics — Determination of tensile properties

KS M ISO 19334-2013

色漆和清漆用粘合剂.松香.气相色谱分析

Binders for paints and varnishes — Gum rosin —   Gas chromatographic analysis

KS M ISO 19378-2005

润滑剂、工业用油和相关产品(L级).机床润滑剂.等级和规范

Lubricants, industrial oils and related   products(class L) －Machine-tool   lubricants－Categories and specifications

KS M ISO 1974-2014

纸.撕裂度的测定(埃尔门多夫法)

Paper — Determination of tearing resistance —   Elmendorf method

KS M ISO 19840-2013

色漆和清漆防护漆系统对钢结构的腐蚀防护粗糙表面上干膜厚度的测量和验收标准

Paints and varnishes ㅡ Corrosion protection of steel structures by protective   paint systems ㅡ Measurement of, and acceptance criteria   for, the thickness of dry films on rough surfaces

KS M ISO 1995-2017

芳香烃.取样

Aromatic hydrocarbons－Sampling

KS M ISO 19952-2006

鞋靴.词汇

Footwear－Vocabulary

KS M ISO 19953-2005

鞋靴.鞋跟的试验方法.抗横向冲击

Footwear－Test methods for heels－Resistance to   lateral impact

KS M ISO 19954-2004

鞋靴.整鞋的试验方法.在家用洗衣机中的可洗性

Footwear－Test methods for whole shoe－Washability in   a domestic washing machine

KS M ISO 19956-2005

鞋具.鞋跟的试验方法.抗疲劳

Footwear－Test methods for heels－Fatigue resistance

KS M ISO 19957-2015

鞋具.鞋跟的试验方法.鞋跟钉保持强度

Footwear－Test methods for heels－Heel pin holding   strength

KS M ISO 19958-2005

鞋靴.鞋跟和顶部的试验方法.顶部保持力

Footwear－Test methods for heels and top pieces－Top   piece retention strength

KS M ISO 1997-2004

粒状软木和软木粉.分类、性质和包装

Granulated cork and cork powder－Classification, properties and   packing

KS M ISO 1998-1-2008

石油工业术语第1部分：原材料和产品

Petroleum industry－Terminology－Part   1：Raw materials and products

KS M ISO 1998-2-2008

石油工业术语第2部分：性能与试验

Petroleum industry－Terminology－Part   2：Properties and tests

KS M ISO 1998-3-2008

石油工业术语第3部分：勘探与生产

Petroleum industry－Terminology－Part   3：Exploration and production

KS M ISO 1998-4-2003

石油工业术语第4部分：精炼

Petroleum industry－Terminology－Part   4：Refining

KS M ISO 1998-5-2003

石油工业术语第5部分：运输、储存、分配

Petroleum industry－Terminology－Part   5：Transport, storage, distribution

KS M ISO 1998-6-2003

石油工业术语第6部分：测量

Petroleum industry－Terminology－Part   6：Measurement

KS M ISO 1998-7-2003

石油工业术语第7部分：杂项术语

Petroleum industry－Terminology－Part   7：Miscellaneous terms

KS M ISO 1998-99-2003

石油工业术语第99部分：总则和索引

Petroleum industry－Terminology－Part   99：General and index

KS M ISO 2000-2017

天然生胶技术规定橡胶（TSR）规格指南

Rubber, raw natural－Guidelines for the specification of   technically specified rubber(TSR)

KS M ISO 2004-2015

浓缩天然胶乳氨保存离心或乳脂型规范

Natural rubber latex concentrate－Centrifuged or   creamed,ammonia-preserved types－Specification

KS M ISO 2005-2009

浓缩天然胶乳污泥含量的测定

Rubber latex, natural, concentrate－Determination of sludge content

KS M ISO 2006-1-2012

合成胶乳机械稳定性的测定第1部分：高速法

Rubber latex, synthetic－Determination of mechanical stability－Part 1：High-speed method

KS M ISO 2006-2-2012

合成胶乳机械稳定性的测定第2部分：负荷中速法

Rubber latex, synthetic－Determination of mechanical stability－Part 2：Moderate-speed method under load

KS M ISO 2007-2007

未硫化橡胶塑性的测定快速塑性计法

Rubber, unvulcanized－Determination of plasticity－Rapid-plastimeter method

KS M ISO 20203-2016

铝生产用含碳材料煅烧焦炭X射线衍射法测定煅烧石油焦的结晶度（LC）

Carbonaceous materials used in the   production of aluminium－Calcined   coke－Determination of crystallite size(Lc) of   calcined petroleum coke by X-ray diffraction

KS M ISO 2023-2007

橡胶鞋衬工业硫化橡胶靴规范

Rubber footwear－Lined industrial vulcanized- rubber   boots－Specification

KS M ISO 2024-2007

有衬里导电橡胶鞋规范

Rubber footwear, lined conducting－Specification

KS M ISO 2025-2008

一般工业用有衬里的耐油胶靴

Lined industrial rubber boots with general   purpose oil resistance

KS M ISO 2027-2009

浓缩、蒸发、保藏天然胶乳规范

Natural rubber latex concentrate,   evaporated, preserved－Specification

KS M ISO 2028-2010

合成胶乳干聚合物的制备

Synthetic rubber latex－Preparation of dry polymer

KS M ISO 20292-2016

原铝生产用材料致密耐火砖耐冰晶石性能的测定

Materials for the production of primary   aluminium－Dense refractory   bricks－Determination of cryolite resistance

KS M ISO 20299-1-2017

橡胶包用薄膜.第1部分：丁二烯橡胶（BR）和丁苯橡胶（SBR）

Film for wrapping rubber bales — Part 1: Butadiene rubber(BR) and   styrene-butadiene rubber(SBR)

KS M ISO 20299-2-2017

橡胶包用薄膜第2部分：天然橡胶

Film for wrapping rubber bales－Part 2：Natural   rubber

KS M ISO 20299-3-2012

橡胶包用薄膜第3部分：三元乙丙橡胶（EPDM）、丁腈橡胶（NBR）、氢化丁腈橡胶（HNBR）、丙烯酸乙烯橡胶（AEM）和丙烯酸橡胶（ACM）

Film for wrapping rubber bales－Part 3：Ethylene-propylene-diene   rubber (EPDM), acrylonitrile-butadiene rubber (NBR), hydrogenated   nitrile-butadiene rubber (HNBR), acrylic-ethylene rubber (AEM) and acrylic   rubber (ACM)

KS M ISO 2030-2004

粒状软木.机械筛分法粒度分析

Granulated cork－Size analysis by mechanical sieving

KS M ISO 2031-2004

粒状软木.体积密度的测定

Granulated cork－Determination of bulk density

KS M ISO 20340-2011

色漆和清漆海上及相关结构用防护漆体系的性能要求

Paints and varnishes－Performance requirements for   protective paint systems for offshore and related structures

KS M ISO 20344-2015

个人保护设备.鞋靴的试验方法

Personal protective equipment－Test methods for footwear

KS M ISO 20345-2015

个人保护设备.安全鞋靴

Personal protective equipment－Safety footwear

KS M ISO 20346-2015

个人保护设备.防护鞋靴

Personal protective equipment－Protective footwear

KS M ISO 20347-2015

个人保护设备.职业鞋靴

Personal protective equipment－Occupational footwear

KS M ISO 2039-1-2003

塑料硬度的测定第1部分：压球法

Plastics－Determination of hardness－Part 1：Ball indentation method

KS M ISO 2039-2-2008

塑料硬度的测定第2部分：洛氏硬度

Plastics－Determination of hardness－Part 2：Rockwell hardness

KS M ISO 20392-2012

绝热材料压缩蠕变试验方法

Thermal-insulating materials－Determination of compressive creep

KS M ISO 20393-2012

隔热材料长期吸水性的测定扩散法

Thermal-insulating materials－Determination of long-term water   absorption by diffusion

KS M ISO 20394-2012

绝热材料抗冻融性的测定

Thermal-insulating materials－Determination of freeze-thaw   resistance

KS M ISO 2040-2002

色漆用铬酸锶颜料

Strontium chromate pigments for paints

KS M ISO 20433-2016

皮革.色牢度试验.耐磨擦色牢度

Leather－Tests for colour fastness－Colour fastness   to crocking

KS M ISO 2049-2012

石油产品颜色测定法（ASTM标度）

Petroleum products－Determination of colour(ASTM scale)

KS M ISO 20562-2015

轮胎气门.ISO心室1、2和3号

Tyre valves－ISO core chambers No. 1, No. 2 and No. 3

KS M ISO 20566-2013

色漆和清漆用实验室洗车机测定涂层系统的耐刮性

Paints and varnishes ㅡ Determination of the scratch resistance of a coating   system using a laboratory car-wash

KS M ISO 20567-1-2011

色漆和清漆涂层耐石屑性的测定第1部分：多次冲击试验

Paints and varnishes－Determination of stone-chip   resistance of coatings－Part 1：Multi-impact testing

KS M ISO 20567-2-2011

色漆和清漆涂层耐石屑性的测定第2部分：导向冲击体单次冲击试验

Paints and varnishes－Determination of stone-chip   resistance of coatings－Part 2：Single-impact test with a guided impact body

KS M ISO 20623-2004

石油及相关产品.用4球法测定流体的极限压力和耐磨性(欧洲条件)

Petroleum and related products－Determination of the extreme-pressure   and anti-wear properties of fluids－Four ball   method(European condition)

KS M ISO 2066-2004

弹性地板覆盖物.集块合成软木含水量的测定

Resilient floor coverings－Determination of moisture content of   agglomerated composition cork

KS M ISO 2067-2004

粒状软木.取样

Granulated cork－Sampling

KS M ISO 2068-2002

色漆用铬酸钡颜料

Barium chromate pigments for paints

KS M ISO 2073-2003

主要用于铝生产的氧化铝.分析用溶液的制备.加压下的盐酸反应法

Aluminium oxide primarily used for the   production of aluminium－Preparation   of solution for analysis－Method by hydrochloric acid   attack under pressure

KS M ISO 20753-2014

塑料.试样

Plastics — Test specimens

KS M ISO 20764-2004

石油和相关产品.水量测定用高沸点流体试验区的准备.氮净化法

Petroleum and related products－Preparation of a test portion of   high-boiling liquids for the determination of water content－Nitrogen purge method

KS M ISO 20783-1-2012

石油及相关产品耐火流体乳化稳定性测定第1部分：HFAE类流体

Petroleum and related products－Determination of emulsion stability   of fire-resistant fluids－Part 1：Fluids in category HFAE

KS M ISO 20783-2-2004

石油及相关产品耐火流体乳化稳定性测定第2部分：HFB类流体

Petroleum and related products－Determination of emulsion stability   of fire-resistant fluids－Part 2：Fluids in category HFB

KS M ISO 20823-2004

石油及相关产品.与热表面接触时液体易燃性的测定.歧管点火试验

Petroleum and related products－Determination of the flammability   characteristics of fluids in contact with hot surfaces－Manifold ignition test

KS M ISO 20843-2012

石油和相关产品.HFAE、HFAS和HFC类别中抗燃液压油pH值的测定

Petroleum and related products－Determination of pH of fire-resistant   fluids within categories HFAE, HFAS and HFC

KS M ISO 20846-2012

石油制品.机动车燃料的硫含量的测定.紫外线荧光法

Petroleum products－Determination of sulfur content of   automotive fuels－Ultraviolet fluorescence method

KS M ISO 20847-2006

石油制品.机动车燃料的硫含量的测定.能量分散X射线荧光光谱法

Petroleum products－Determination of sulfur content of   automotive fuels－Energy－dispersive   X－ray fluorescence spectrometry

KS M ISO 20863-2005

鞋靴.补强胶条和皮鞋包头的试验方法.粘合性

Footwear－Test methods for stiffeners and toepuffs－Bondability

KS M ISO 20864-2005

鞋靴.补强胶条和皮鞋包头的试验方法.机械特性

Footwear－Test methods for stiffeners and toepuffs－Mechanical   characteristics

KS M ISO 20865-2008

鞋类.外底的试验方法.压缩能

Footwear－Test methods for outsoles－Compression   energy

KS M ISO 20866-2012

鞋类.内底试验方法.耐脱层性

Footwear－Test methods for insoles－Delamination   resistance

KS M ISO 20867-2012

鞋类.内底试验方法.跟钉抓紧强度

Footwear－Test methods for insoles－Heel pin holding   strength

KS M ISO 20868-2012

鞋类.内底试验方法.耐磨损性

Footwear－Test methods for insoles－Abrasion   resistance

KS M ISO 20869-2012

鞋类.外底、内底、鞋衬和内垫试验方法.溶水量

Footwear－Test methods for outsoles, insoles, lining and insocks－Water soluble content

KS M ISO 20870-2012

鞋类.老化条件

Footwear－Ageing conditioning

KS M ISO 20871-2012

鞋类外底试验方法耐磨性

Footwear－Test methods for outsoles－Abrasion   resistance

KS M ISO 20872-2012

鞋类.外底试验方法.耐撕裂强度

Footwear－Test methods for outsoles－Tear strength

KS M ISO 20873-2012

鞋类.外底试验方法.尺寸稳定性

Footwear－Test methods for outsoles－Dimensional   stability

KS M ISO 20874-2012

鞋类.外底试验方法.针孔撕裂强度

Footwear－Test methods for outsoles－Needle tear   strength

KS M ISO 20875-2012

鞋类.外底试验方法.耐撕裂强度和耐脱层性的测定

Footwear－Test methods for outsoles－Determination of   split tear strength and delamination resistance

KS M ISO 20876-2012

鞋类.内底试验方法.耐缝合处撕裂

Footwear－Test methods for insoles－Resistance to   stitch tear

KS M ISO 20877-2013

鞋类.整鞋试验方法.隔热

Footwear ㅡ   Test methods for whole shoe ㅡ Thermal insulation

KS M ISO 20884-2012

石油制品.机动车燃料的硫含量的测定.波长色散X射线荧光光谱法

Petroleum products－Determination of sulfur content of   automotive fuels－Wavelength-dispersive X-ray   fluorescence spectrometry

KS M ISO 2096-2017

工业用甘油.取样方法

Glycerols for industrial use — Methods of sampling

KS M ISO 21003-1-2014

建筑物内冷热水用多层管道系统第1部分：总则

Multilayer piping systems for hot and cold   water installations inside buildings — Part 1: General

KS M ISO 21003-2-2014

建筑物内冷热水用多层管道系统第2部分：管道

Multilayer piping systems for hot and cold   water installations inside buildings — Part 2: Pipes

KS M ISO 21003-3-2014

建筑物内冷热水用多层管道系统第3部分：配件

Multilayer piping systems for hot and cold   water installations inside buildings — Part 3: Fittings

KS M ISO 21003-5-2014

建筑物内冷热水用多层管道系统第5部分：系统适用性

Multilayer piping systems for hot and cold   water installations inside buildings — Part 5: Fitness for purpose of the system

KS M ISO 21003-7-2014

建筑物内冷热水用多层管道系统第7部分：合格评定指南

Multilayer piping systems for hot and cold   water installations inside buildings — Part 7: Guidance for the assessment of conformity

KS M ISO 21138-1-2008

无压地下排水塑料管道系统未增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE）结构壁管道系统第1部分：管道、配件和系统的材料规范和性能标准

Plastics piping systems for non-pressure   underground drainage and sewerage－Structured-wall piping systems of unplasticized poly(vinyl   chloride)(PVC-U), polypropylene(PP) and polyethylene(PE)－Part 1：Material specifications and   performance criteria for pipes, fittings and system

KS M ISO 21138-2-2008

无压地下排水塑料管道系统未增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE）结构壁管道系统第2部分：A型光滑外表面管道及配件

Plastics piping systems for non-pressure   underground drainage and sewerage－Structured-wall piping systems of unplasticized poly(vinyl   chloride)(PVC-U), polypropylene(PP) and polyethlyene(PE)－Part 2：Pipes and fittings with smooth   external surface, Type A

KS M ISO 21138-3-2008

无压地下排水塑料管道系统未增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE）结构壁管道系统第3部分：外表面不光滑的B型管道及配件

Plastics piping systems for non-pressure   underground drainage and sewerage－Structured-wall piping systems of unplasticized poly(vinyl   chloride)(PVC-U), polypropylene(PP) and polyethlyene(PE)－Part 3 : Pipes and fittings with non-smooth external surface, Type   B

KS M ISO 2114-2010

塑料(聚酯树脂)、色漆和清漆(胶粘剂).部分酸值和总酸值的测定

Plastics(polyester resins) and paints and   varnishes(binders)－Determination   of partial acid value and total acid value

KS M ISO 21148-2007

化妆品微生物检验通则

Cosmetics－Microbiology－General   instructions for microbiological examination

KS M ISO 21149-2007

化妆品微生物学需氧嗜中温细菌的计数与检测

Cosmetics－Microbiology－Enumeration and   detection of aerobic mesophilic bacteria

KS M ISO 21150-2017

化妆品微生物学大肠杆菌检测

Cosmetics－Microbiology－Detection of   Escherichia coli

KS M ISO 2120-2017

工业用液氯.蒸发物中氯(体积)含量的测定

Liquid chlorine for industrial use — Determination of the content of   chlorine by volume in the vaporized product

KS M ISO 2121-2017

工业用液氯.水含量的测定.重量法

Liquid chlorine for industrial use — Determination of water content — Gravimetric method

KS M ISO 2122-2017

工业用硅酸钠和硅酸钾.不易溶于沸水的产品溶液的制备和不溶于水物质的测定

Sodium and potassium silicates for   industrial use —   Preparation of solution of products not easily soluble in boiling water and   determination of matter insoluble in water

KS M ISO 21227-1-2009

色漆和清漆光学成像法评定涂层表面缺陷第1部分：通用指南

Paints and varnishes－Evaluation of defects on coated   surfaces using optical imaging－Part 1：General guidance

KS M ISO 21227-2-2012

色漆和清漆光成像法评定涂层表面缺陷第2部分：多冲击石屑试验评定程序

Paints and varnishes－Evaluation of defects on coated   surfaces using optical imaging－Part 2：Evaluation procedure for multi-impact stone-chipping test

KS M ISO 21227-3-2012

色漆和清漆光学成像法评定涂层表面缺陷第3部分：划痕周围分层和腐蚀的评定

Paints and varnishes－Evaluation of defects on coated   surfaces using optical imaging－Part 3：Evaluation of delamination and corrosion around a scribe

KS M ISO 21227-4-2012

色漆和清漆光成像法评定涂层表面缺陷第4部分：丝状腐蚀的评定

Paints and varnishes－Evaluation of defects on coated   surfaces using optical imaging－Part 4：Evaluation of filiform corrosion

KS M ISO 21268-1-2008

土壤质量－土壤和土壤材料后续化学和生态毒理学试验的淋滤程序－第1部分：2 l/kg干物质液固比分批试验

Soil quality－Leaching procedures for subsequent chemical and   ecotoxicological testing of soil and soil materials－Part   1：Batch test using a liquid to solid ratio of 2 L/kg   dry matter

KS M ISO 21268-2-2008

土壤质量－土壤和土壤材料后续化学和生态毒理学试验的淋滤程序－第2部分：用10 l/kg干物质的液固比分批试验

Soil quality－Leaching procedures for subsequent chemical and   ecotoxicological testing of soil and soil materials－Part   2：Batch test using a liquid to solid ratio of 10 L/kg   dry matter

KS M ISO 21268-3-2008

土壤质量.土壤和土壤材料后续化学和生态毒理学试验的淋滤程序.第3部分：上流渗滤试验

Soil quality－Leaching procedures for subsequent chemical and   ecotoxicological testing of soil and soil materials－Part   3：Up-flow percolation test

KS M ISO 21268-4-2008

土壤质量-土壤和土壤材料后续化学和生态毒理学试验的淋滤程序-第4部分：初始酸/碱添加对淋滤的影响

Soil quality－Leaching procedures for subsequent chemical and   ecotoxicological testing of soil and soil materials－Part   4：Influence of pH on leaching with initial acid/base   addition

KS M ISO 2131-2006

表面活性剂.简化分类法

Surface active agents-Simplified   classification

KS M ISO 21367-2014

塑料.对火的反应.垂直定向样品火焰蔓延和燃烧产物释放的试验方法

Plastics — Reaction to fire — Test   method for flame spread and combustion product release from vertically   oriented specimens

KS M ISO 2137-2016

石油产品.润滑脂和石油脂.锥入度的测定

Petroleum products and lubricants — Determination of conepenetration of   lubricating greases and petrolatum

KS M ISO 2144-2016

纸、纸板和纸浆.900℃燃烧残留物(灰分)的测定

Paper, board and pulps－Determination of residue(ash) on   ignition at 900℃

KS M ISO 21461-2017

橡胶－硫化橡胶化合物中油芳香性的测定

Rubber－Determination of the aromaticity of oil in vulcanized rubber   compounds

KS M ISO 21509-2014

塑料和硬橡胶.肖氏硬度计的检验

Plastics and ebonite — Verification of Shore durometers

KS M ISO 2160-2012

石油产品铜片腐蚀性试验方法

Petroleum products－Corrosiveness to copper－Copper strip test

KS M ISO 216-2008

书写纸和某些印刷品－裁切尺寸－A和B系列，以及机器方向指示

Writing paper and certain classes of   printed matter－Trimmed sizes－A and B series, and indication of machine direction

KS M ISO 21687-2016

铝生产用含碳材料氦气体比重法（容量法）测定密度气固材料

Carbonaceous materials used in the   production of aluminium－Determination   of density by gas pyknometry (volumetric) using helium as the analysis gas－Solid materials

KS M ISO 217-2016

纸－未裁切尺寸－主要和辅助范围的名称与公差，以及机器方向指示

Paper－Untrimmed sizes－Designation and tolerances   for primary and supplementary ranges, and indication of machine direction

KS M ISO 2174-2006

表面活性剂.已知钙硬度水的制备

Surface active agents－Preparation of water with known calcium   hardness