化学类标准(四)
2019-07-23 21:39标准号 | 中文名称 | 英文名称 |
KS M 8071-2004 | 间甲酚 | m-Cresol |
KS M 8072-2004 | 对甲酚 | p-Cresol |
KS M 8074-2004 | 三氯化碘 | Iodine trichloride |
KS M 8075-2004 | 六氯铂酸钾 | Potassium hexachloroplatinate(Ⅳ) |
KS M 8076-2015 | 叠氮化钠 | Sodium azide |
KS M 8077-2004 | 氯化1,10菲绕啉(一水合物) | 1, 10-Phenanthrolinium chloride monohydrate |
KS M 8078-2015 | 磷酸氢化二钾 | Dipotassium hydrogenphosphate |
KS M 8079-2004 | 硫酸镁(七水合物) | Magnesium sulfate heptahydrate |
KS M 8080-2005 | 锑 | Antimony |
KS M 8088-2015 | 硫磺 | Sulfur |
KS M 8092-2015 | 红紫靛 | Indigo carmine |
KS M 8107-2005 | 氧化锌 | Zinc oxide |
KS M 8112-2006 | 亚硫酸钠(七水合物) | Sodium sulfite heptahydrate |
KS M 8113-2015 | 亚硫酸钠(无水合物) | Sodium sulfite |
KS M 8117-2012 | 硫氰酸钠 | Sodium thiocyanate |
KS M 8125-2006 | 硫酸铜(无水合物) | Copper(II) sulfate(Anhydrous) |
KS M 8126-2005 | 硫酸铁(n水合物) | Iron(III) sulfate n-hydrate |
KS M 8138-2015 | 氯酸铜(i) | Copper(I) chloride |
KS M 8155-2012 | 轻石油 | Ligroin |
KS M 8156-2012 | 乙二醇 | Ethylene glycol |
KS M 8157-2015 | 苯胺 | Aniline |
KS M 8165-2004 | 三氧化锑 | Antimony trioxide |
KS M 8173-2005 | 2,6-二溴-n-氯-p-苯醌一亚胺 | 2,6-Dibromo-N-chloro-p-benzoquinone monoimine(reagent) |
KS M 8175-2015 | 苯酚 | Phenol |
KS M 8213-2005 | 2-甲氧基乙醇 | 2-Methoxyethanol |
KS M 8221-2015 | 正已烷 | n-Hexane |
KS M 8225-2006 | 甲基橙 | Methyl orange |
KS M 8226-2015 | 茜素红 | Alizarin red S |
KS M 8227-2006 | 氯化铁六水合物 | Iron(III) chloride hexahydrate |
KS M 8230-2006 | 硫化钠九水合物 | Sodium sulfide nonahydrate |
KS M 8234-2006 | 硝酸铅(Ⅱ) | Lead(II) nitrate |
KS M 8236-2008 | 硝基苯 | Nitrobenzene |
KS M 8238-2015 | 酚酞 | Phenolphthalein |
KS M 8241-2015 | 嘧啶 | Pyridine |
KS M 8249-2015 | 高碘酸钾 | Potassium periodate |
KS M 8250-2015 | 三氧化二砷 | Diarsenic trioxide |
KS M 8251-2015 | 草酸纳 | Sodium oxalate |
KS M 8252-2012 | 氨基磺酸 | Amidosulfuric acid |
KS M 8255-2015 | 苯(甲)酸 | Benzoic acid |
KS M 8258-2015 | 高碘酸钠 | Sodium periodate |
KS M 8260-2015 | 蚁酸 | Formic acid |
KS M 8263-2012 | N,N-二乙基二硫代氨基甲酸钠三水合物 | Sodium N,N-diethyldithiocarbamate trihydrate |
KS M 8264-2015 | 丁二酮肟 | Dimethylglyoxime |
KS M 8266-2015 | 5-磺基水杨酸(二水合物) | 5-Sulfosalicylic acid dihydrate |
KS M 8268-2012 | 羊毛铬黑t | Eriochrome black T |
KS M 8269-2012 | 8-醌基 | 8-Quinolinol |
KS M 8270-2015 | 二硫化钾 | Potassium disulfate |
KS M 8271-2012 | 1,10-菲罗啉一水合物 | 1,10-Phenanthroline monohydrate |
KS M 8273-2015 | 硫酸肼 | Hydrazinium sulfate |
KS M 8274-2015 | 亚甲基蓝 | Methylene blue |
KS M 8275-2015 | 酚红 | Phenol red |
KS M 8276-2015 | 尿素 | Thiourea |
KS M 8277-2012 | 碳酸铵 | Ammonium carbonate |
KS M 8278-2012 | 汞 | Mercury |
KS M 8281-2008 | 邻甲酚 | o-Cresol |
KS M 8286-2015 | 高氯酸钠(一水合物) | Sodium perchlorate monohydrate |
KS M 8287-2012 | 庚烷 | Heptane |
KS M 8288-2015 | 石蜡 | Paraffin |
KS M 8292-2012 | 六氯铂酸氢(IV)六水合物 | Hydrogen hexachloroplatinate(IV) hexahydrate |
KS M 8296-2012 | 氯化钯 | Palladium(II) chloride |
KS M 8297-2012 | d(+)葡萄糖 | D(+)Glucose |
KS M 8298-2015 | 甲酰胺 | Formamide |
KS M 8299-2012 | 乙酸钡 | Barium acetate |
KS M 8302-2005 | 氯酸钾 | Potassium chlorate |
KS M 8304-2015 | 硝酸钠 | Sodium nitrite |
KS M 8307-2015 | 氯化铝(iii)(六水合物) | Aluminium(III) chloride hexahydrate |
KS M 8309-2005 | 氯化镍(ii)(六水合物) | Nickel(II) chloride hexahydrate |
KS M 8312-2005 | 琼脂 | Agar |
KS M 8313-2006 | 醋酸钙(一水合物) | Calcium acetate monohydrate |
KS M 8316-1996 | 乙酸锌(二水合物) | Zinc acetate dihydrate |
KS M 8317-2006 | 水杨酸 | Salicylic acid |
KS M 8318-2015 | 乙酸钾 | Potassium acetate |
KS M 8319-2006 | 硬脂酸 | Stearic acid |
KS M 8321-2015 | 1,2-二氯乙烷 | 1,2-Dichloroethane CH 2 ClCH 2 Cl FW:98.96 |
KS M 8322-2001 | 汽油 | Petroleum benzine |
KS M 8323-2015 | 刚果红 | Congo red |
KS M 8326-2012 | 蔗糖 | Sucrose |
KS M 8331-2015 | 乙醛 | Acetaldehyde |
KS M 8332-2005 | 铝 | Aluminium |
KS M 8335-2015 | 1-辛醇 | 1-Octanol |
KS M 8336-2005 | 高氯酸镁 | Magnesium perchlorate |
KS M 8337-2015 | 硫酸钾铝(十二水合物) | Aluminium potassium sulfate 12-water |
KS M 8338-2015 | 蚁酸纳 | Sodium formate |
KS M 8341-2015 | 铬酸钾 | Potassium chromate |
KS M 8342-2005 | 乙酸纳 | Sodium acetate |
KS M 8343-2005 | 喹啉 | Quinoline |
KS M 8345-2005 | 氯化锑(iii) | Antimony(III) chloride |
KS M 8346-2015 | 氧化钙 | Calcium oxide |
KS M 8348-2005 | 氰化钠 | Sodium cyanide |
KS M 8351-2015 | 二苯胺 | Dipheylamine |
KS M 8352-2015 | 甲基黄 | Methyl yellow |
KS M 8355-2005 | 高纯化学试剂.硝酸 | Highly purified nitric acid |
KS M 8356-2005 | 高纯化学试剂.盐酸 | Highly purified hydrochloric acid |
KS M 8357-2005 | 高纯化学试剂.氨水 | Highly purified ammonia solution |
KS M 8358-2005 | 高纯化学试剂.高氯酸 | Highly purified perchloric acid |
KS M 8360-2015 | 硝酸铝(九水合物) | Aluminum nitrate nonahydrate |
KS M 8362-2005 | 硝酸钡 | Barium nitrate |
KS M 8363-2005 | 硝酸镁(六水合物) | Magnesium nitrate hexahydrate |
KS M 8364-2014 | 锡 | Tin (Reagent) |
KS M 8367-2014 | 百里酚蓝 | Thymol blue (Reagent) |
KS M 8368-2005 | 铜 | Copper |
KS M 8369-2005 | 三氯乙烯 | Trichloroethylene |
KS M 8372-2017 | 氰化甲烷 | Acetonitrile |
KS M 8373-2014 | 4-氨基安替比林 | 4-Amino antipyrine (Reagent) |
KS M 8374-2014 | 3-甲基-1-丁醇 | 3-Methyl-1-butanol(Reagent) |
KS M 8378-2006 | 二甲苯阿尼林ff | Xylene cyanol FF |
KS M 8379-2014 | 铜铁试剂 | Cupferron (Reagent) |
KS M 8380-2014 | 甲酚红 | Cresol red (Reagent) |
KS M 8383-2015 | 乙酸丁酯 | Butyl acetate |
KS M 8384-2015 | 乙酸甲酯 | Methyl acetate |
KS M 8385-2014 | 邻羟基苯醛 | Salicylaldehyde (Reagent) |
KS M 8386-2006 | 水杨酸钠 | Sodium salicylate |
KS M 8387-2006 | 双硫腙 | Dithizone |
KS M 8388-2006 | l-天冬酰胺酸(一水合物) | L-Asparagine monohydrate |
KS M 8390-2014 | 硝酸钾(四水合物) | Calcium nitrate tetrahydrate (Reagent) |
KS M 8391-2006 | 磷酸氢二铵(Ⅳ) | Diammonium cerium(IV) nitrate |
KS M 8392-2001 | 硝酸钍(四水合物) | Thorium nitrate tetrahydrate |
KS M 8393-2014 | 硝酸锰(Ⅱ)(六水合物) | Manganese(Ⅱ) nitrate hexahydrate (Reagent) |
KS M 8394-2014 | 对氨基苯磺酸 | Sulfanilic acid(Reagent) |
KS M 8395-2014 | 氨基磺酸盐铝 | Ammonium amidosulfate(Reagent) |
KS M 8396-2014 | 钠钙 | Soda lime (Reagent) |
KS M 8397-2015 | 乙酰丙酮 | Acetylacetone |
KS M 8399-2006 | 巯基乙酸 | Mercapto acetic acid |
KS M 8401-2014 | 钠 | Sodium(Reagent) |
KS M 8402-2006 | 对萘基苯 | p-Naphtholbenzein |
KS M 8403-2015 | 柠檬酸氢二铵 | Diammonium hydrogen citrate |
KS M 8404-2015 | 氯化钛(Ⅳ) | Titanium(IV) oxide |
KS M 8405-2006 | 硝基苯胺 | P-Nitrophenol |
KS M 8406-2015 | 尿素 | Urea |
KS M 8407-2006 | 丙烯酸 | Hydroquinone |
KS M 8408-2015 | 2-丁醇 | 2-Butanol |
KS M 8411-2006 | 丙二醇 | Propylene glycol |
KS M 8412-2015 | 硫酸锰(Ⅱ)五水合物 | Manganese(II) sulfate pentahydrate |
KS M 8414-2015 | 邻苯二甲酸氢碳 | Potassium hydrogen carbonate |
KS M 8415-2006 | 氯化2,3,5-三苯基-2h-四唑 | 2,3,5-Triphenyl-2H-tetrazolium chloride |
KS M 8417-2006 | 3-甲基-1-苯-5-吡唑啉酮 | 3-Methyl-1-phenyl-5-pyrazolone |
KS M 8418-2006 | 2-氨基-2-羟甲-1,3-丙二醇 | 2-Amino-2-hydroxymethyl-1,3-propanediol |
KS M 8420-2012 | l-氨酸 | L-Tryptophan |
KS M 8421-2012 | 硫酸钠(十水合物) | Sodium sulfate decahydrate |
KS M 8422-2012 | l-萘酚 | 1-Naphthol |
KS M 8423-2012 | 2-萘酚 | 2-Naphthol |
KS M 8424-2012 | 2,2'-亚氨基盐酸乙醇胺 | 2,2′-Iminodiethanol |
KS M 8425-2015 | 硫酸铵溶液 | Ammonium sulfide solution |
KS M 8430-2012 | 荧光素 | Uranine |
KS M 8431-2015 | 1-丙醇 | 1-Propanol |
KS M 8432-2012 | 六甲基四咪唑 | Hexamethylenetetramine |
KS M 8434-2012 | 亚硫酸氢钠 | Sodium hydrogensulfite |
KS M 8435-2012 | 盐酸萘乙二胺 | N-1-Naphthylethylenediamine dihydrochloride |
KS M 8436-2015 | 硫化铁(Ⅱ) | Iron(II) sulfide |
KS M 8439-2012 | 硫化四铵铈(Ⅳ)(二水合物) | Tetraammonium cerium(Ⅳ) sulfate dihydrate |
KS M 8440-2008 | 硫酸镍(Ⅱ)(六水合物) | Nickel(II) sulfate hexahydrate |
KS M 8441-2012 | 苯二酚 | Resorcinol |
KS M 8442-2012 | l-胱氨酸 | L(-)-Cystine |
KS M 8443-2012 | 一水合二安替吡啉甲烷 | Diantipyrylmethane monohydrate |
KS M 8445-2015 | 二甲基亚砜 | Dimethyl sulfoxide |
KS M 8446-2012 | 2,2,4-三甲基戊烷 | 2,2,4-Trimethylpentane |
KS M 8447-2012 | 大肠菌DNA聚合酶Ⅰ | DNA polymerase I(E.coli) |
KS M 8449-2012 | 5´-腺苷酸 | 5´-Adenylic acid |
KS M 8450-2012 | 高纯硫酸 | Highly purified sulfuric acid |
KS M 8451-2012 | 高纯氢氧化钠溶液 | Highly purified sodium hydroxide solution |
KS M 8452-2012 | 2,2′,2〃-nitorilotriethanol | 2,2′,2″-Nitorilotriethanol |
KS M 8453-2015 | 4-甲基-2-戊酮 | 4-Methyl-2-pentanone |
KS M 8455-2012 | 高氯酸钡 | Barium perchlorate |
KS M 8456-2012 | 三氯乙酸 | Trichloroacetic acid |
KS M 8457-2015 | 溴化钾 | Potassium bromide |
KS M 8458-2012 | 玻璃绒 | Glass wool |
KS M 8459-2015 | 2,3-吲哚因二酮 | 2,3-Indolinedione |
KS M 8460-2015 | 二硫化碳 | Carbon disulfide |
KS M 8462-2008 | 四氢呋喃 | Tetrahydrofuran |
KS M 8463-2008 | 二乙基二硫代氨基甲酸银 | Silver N,N-diethyldithiocarbamate |
KS M 8464-2015 | 二苯胺钠-4-磺酸盐 | Sodium diphenylamine-4-sulfonate |
KS M 8466-2008 | 1,1,2,2-四氯乙烷 | 1,1,2,2-Tetrachloroethane |
KS M 8467-2015 | 四苯硼酸钠 | Sodium tetraphenylborate |
KS M 8470-2008 | 二异丙基乙醚 | Diisopropyl ether |
KS M 8472-2008 | 3-甲基-1-苯基-5-吡唑啉酮 | Bis(3-methyl-1-phenyl-5-pyrazolone) |
KS M 8473-2008 | 苯芴酮 | Phenylfluorone |
KS M 8474-2008 | 聚乙烯醇 | Polyvinyl alcohol |
KS M 8475-2008 | 甲基百里酚蓝 | Methylthymol blue |
KS M 8476-2008 | n-溴琥珀酰亚胺 | N-bromosuccinimide |
KS M 8479-2008 | 二甲苯酚橙色 | Xylenol orange |
KS M 8480-2008 | 苯甲酰苯胲 | N-Benzoyl-N-Phenylhydroxylamine |
KS M 8487-2015 | l-丙胺酸 | L-Alanine |
KS M 8488-2015 | l-羟(基)脯氨酸 | L-hydroxyproline |
KS M 8489-2008 | l(+)-谷氨酸盐 | L(+)-Glutamine |
KS M 8490-2015 | l-丝氨酸 | L-Serine |
KS M 8491-2008 | l-缬氨酸 | L-Valine |
KS M 8492-2008 | l-脯氨酸 | L(-)-Proline |
KS M 8493-2008 | 若丹明b | Rhodamine B |
KS M 8494-2008 | 四溴酚酞乙酯钾盐 | Tetrabromophenolphthalein ethylester potassium salt |
KS M 8495-2015 | l-天冬氨酸 | L-Aspartic Acid |
KS M 8496-2015 | l-谷氨酸 | L-Glutamic Acid |
KS M 8497-2008 | l-组氨酸组氨酸(一水合物) | L-Histidine hydrochloride monohydrate |
KS M 8498-2008 | l-亮氨酸 | L-Leucine |
KS M 8504-2008 | 4-(2-羟乙基)哌嗪-1-乙磺酸 | HEPES〔2-[4-(2-Hydroxyethyl)-1-piperazinyl]ethanesulfonic acid〕 |
KS M 8505-2008 | PIPES1,4-哌嗪二乙磺酸 | PIPES[Piperazine-1, 4-bis(2-ethanesulfonic acid)] |
KS M 8506-2008 | 三嗪N-[三(羟甲基)甲基]甘氨酸] | Tricine N-[Tris(Hydroxymethyl)methyl]glycine〕 |
KS M 8507-2015 | 钼酸二钠(六)二水合物Na2Moo4_2H2O fw:241.95 | Disodium molybdate(Ⅵ) dihydrate Na2MoO4ㆍ2H2O FW:241.95 |
KS M 8509-2015 | 残留农药和多氯联苯(PCBs)的测定用乙腈 | Acetonitrile for pesticide residue and polychlorinated biphenyl analysis |
KS M 8510-2004 | 残留农药和多氯联苯(PCBs)的测定用丙酮 | Acetone for pesticide residue and polychlorinated biphenyl analysis |
KS M 8511-2015 | 残留农药和多氯联苯(PCBs)的测定用乙醇(99.5) | Ethanol for pesticide residue and polychlorinated biphenyl analysis |
KS M 8512-2004 | 2氨基乙醇 | 2-Aminoethanol |
KS M 8513-2004 | 农药残留量的测定用二氯甲 | Dichloromethane for pesticide residue analysis |
KS M 8514-2004 | 氧化剂分析用磷酸二氢钾 | Potassium dihydrogenphosphate for oxidant analysis |
KS M 8515-2004 | 二硫二丁基 | Dibutyl disulfide |
KS M 8516-2004 | N,N-二甲基苯二胺二氯化铵 | N, N-Dimethylpphenylenediammonium dichloride |
KS M 8517-2004 | 氨基乙酸 | Glycine |
KS M 8518-2004 | 三水合物对甲苯磺酸氯胺钠 | Sodium ptoluenesulfonchloramide trihydrate |
KS M 8520-2004 | 盐酸半胱氨酸一水合物 | LCysteine hydrochloride monohydrate |
KS M 8523-2004 | 酒石酸钾半水合物 | Potassium (+)tartrate hemihydrate |
KS M 8524-2004 | 酒石酸氢钾(+) | Potassium hydrogen (+)tartrate |
KS M 8526-2015 | 磷酸氢二钠 | Disodium hydrogenphosphate |
KS M 8529-2015 | 茚三酮 | Ninhydrin |
KS M 8530-2015 | 残留农药和多氯联苯(PCBs)的测定用己烷 | Hexane for pesticide residue and polychlorinated biphenyl analysis |
KS M 8531-2004 | 氮含量测定用氢氧化钠 | Sodium hydroxide for nitrogen compounds analysis |
KS M 8532-2004 | 氧化剂测定用碘化钾 | Potassium iodide for oxidant analysis |
KS M 8533-2004 | 氧化剂测定用十二水合磷酸氢二钠 | Disodium hydrogenphosphate 12-hydrate for oxidant analysis |
KS M 8534-2004 | 镁 | Magnesium |
KS M 8535-2004 | 间甲酚紫色 | Metacresol purple |
KS M 8537-2004 | 硫酸银 | Silver sulfate |
KS M 8538-2004 | 一水合硫酸锂 | Lithium sulfate monohydrate |
KS M 8540-2005 | 1-氨基-2-萘酚-4-磺酸 | 1-Amino-2-naphthol-4-sulfonic acid |
KS M 8542-2015 | 氯化锶(六水合物) | Strontium chloride hexahydrate |
KS M 8544-2005 | 氯化铜(ii)(二水合物) | Copper(II) chloride dihydrate |
KS M 8545-2005 | 氯化锰(ii)(四水合物) | Manganese(II) chloride tetrahydrate |
KS M 8547-2015 | 铬变素磷酸氢二钠(二水合物) | Disodium chromotropate dihydrate |
KS M 8550-2015 | 氯化钛(iii)水 | Titanium(III) chloride solution |
KS M 8552-2015 | 环己醇 | Cyclohexanol |
KS M 8553-2015 | 环己酮 | Cyclohexanone |
KS M 8554-2005 | ρ-二甲氨基苯甲醛绕丹宁 | p-Dimethylaminobenzylidene rhodanine |
KS M 8555-2005 | ρ-二甲基苯甲醛 | p-Dimethylaminobenzaldehyde |
KS M 8556-2015 | 硝酸钴(ii)(六水合物) | Cobalt(II) nitrate hexahydrate |
KS M 8557-2015 | 硫代硫酸钠 | Sodium thiosulfate |
KS M 8559-2015 | 百里酚酞 | Thymolphthalein |
KS M 8560-2003 | 锂钴氧化物 | Lithium cobalt oxide |
KS M 9245-2008 | 油漆和颜料中氯酚类含量分析方法 | Determination of chlorophenols in industrial products as paint, dye |
KS M 9720-2004 | 无机化工产品氯化物含量测定的通用方法(汞量法) | Inorganic chemical products for industrial use-General method for determination of chloride content(Mercurimetric method) |
KS M 9721-2017 | 高分子材料中多环芳烃的测定 | Determination of PAHs (polycyclic aromatic hydrocarbons) in polymer materials |
KS M 9722-2017 | 化工产品中PFOS/PFOA化学品的测定 | Determination of PFOS/PFOA chemicals in chemical products |
KS M 9723-2017 | 氰化金钾中金的测定方法 | Methods for determination of gold in potassium gold cyanide |
KS M IEC 60695-11-2005 | 着火危险试验.第11-10部分:试验火焰.50W水平及垂直火焰试验法 | Fire hazard testing-Part 11-10:Test flames-50W horizontal and vertical flame test methods |
KS M IEC 60695-11-2005 | 着火危险试验.第11-10部分:试验火焰.50W水平及垂直火焰试验法 | Fire hazard testing-Part 11-20:Test flames-500W flame test methods |
KS M ISO 10050-2008 | 润滑剂、工业用油及有关产品(L类)-T系列(涡轮机)-三芳基磷酸酯涡轮机控制液规范(ISO-L-TCD类) | Lubricants, industrial oils and related products(class L)-Family T(Turbines)-Specifications of triaryl phosphate ester turbine control fluids(category ISO-L-TCD) |
KS M ISO 10051-2012 | 热绝缘-传热中的水分效应-潮湿材料热传递系数的测定 | Thermal insulation-Moisture effects on heat transfer-Determination of thermal transmissivity of a moist material |
KS M ISO 10082-2007 | 塑料酚醛树脂分类和试验方法 | Plastics-Phenolic resins-Classification and test methods |
KS M ISO 10093-2014 | 塑料.燃烧试验.标准点火源 | Plastics — Fire tests — Standard ignition sources |
KS M ISO 10106-2004 | 软木塞.总迁移的测定 | Cork stoppers-Determination of global migration |
KS M ISO 10123-2015 | 粘合剂.用针-环试件测定厌氧胶粘剂的剪切强度 | Adhesives????Determination of shear strength of anaerobic adhesives using pin-and-collar specimens |
KS M ISO 10130-2014 | 化妆品.分析方法.亚硝胺:用高效液相色谱法、柱后光解和衍生法检测和测定化妆品中的N-亚硝二乙醇胺 | Cosmetics — Analytical methods — Nitrosamines: Detection and determination of N-nitrosodiethanolamine(NDELA) in cosmetics by HPLC, post-column photolysis and derivatization |
KS M ISO 10142-2004 | 铝生产用碳素材料.煅烧焦.用实验室振动磨测定粒度稳定性 | Carbonaceous materials for use in the production of aluminium - Calcined coke - Determination of grain stability using a laboratory vibration mill |
KS M ISO 10143-2004 | 铝生产用碳素材料.电极用煅烧焦.颗粒电阻率的测定 | Carbonaceous materials for the production of aluminium-Calcined coke for electrodes-Determination of the electrical resistivity of granules |
KS M ISO 10146-2004 | 交联聚乙烯(PE-X)管材.时间和温度对预期强度的影响 | Crosslinked polyethylene(PE-X) pipes-Effect of time and temperature of the expected strength |
KS M ISO 10147-2016 | 交联聚乙烯(PE-X)制管和配件.通过测定凝胶含量测定交联度 | Pipes and fittings made of crosslinked polyethylene (PE-X)- Estimation of the degree of crosslinking by determination of the gel content |
KS M ISO 10191-2012 | 轿车轮胎检验轮胎性能实验室试验方法 | Passenger car tyres-Verifying tyre capabilities-Laboratory test methods |
KS M ISO 10231-2010 | 摩托车轮胎轮胎性能试验方法 | Motorcycle tyres-Test methods for verifying tyre capabilities |
KS M ISO 10236-2004 | 铝生产用碳素材料.电极用生焦和煅烧焦.松(紧装)密度的测定 | Carbonaceous materials for the production of aluminium-Green coke and calcined coke for electrodes-Determination of bulk density(tapped) |
KS M ISO 10282-2016 | 一次性无菌橡胶外科手套.规范 | Single-use sterile rubber surgical gloves-Specification |
KS M ISO 10283-2012 | 色漆和清漆用粘合剂.聚异氰酸酯树脂中二异氰酸酯单体的测定 | Binders for paints and varnishes- Determination of monomeric diisocyanates in isocyanate resins |
KS M ISO 10307-1-2011 | 石油产品.残余燃料油中总沉淀物.第1部分:热过滤法测定 | Petroleum products-Total sediment in residual fuel oils-Part 1:Determination by hot filtration |
KS M ISO 10307-2-2014 | 石油产品.残余燃料油中的总沉淀物.第2部分:用标准老化程序测定 | Petroleum products — Total sediment in residual fuel oils — Part 2: Determination using standard procedures for ageing |
KS M ISO 10335-2003 | 橡胶和塑料鞋命名方法 | Rubber and plastics footwear-Nomenclature |
KS M ISO 10336-2008 | 原油.水分的测定.容量卡尔·费休滴定法 | Crude petroleum-Determination of water-Potentiometric Karl Fischer titration method |
KS M ISO 10337-2003 | 原油.水分的测定.库仑卡尔·费休滴定法 | Crude petroleum-Determination of water-Coulometric Karl Fischer titration method |
KS M ISO 10349-1-2002 | 摄影照相级化学品试验方法第1部分:总则 | Photography-Photographic-grade chemicals-Test methods-Part 1:General |
KS M ISO 10349-10-2002 | 摄影照相级化学品试验方法第10部分:硫化物含量的测定 | Photography-Photographic-grade chemicals-Test methods-Part 10:Determination of sulfide content |
KS M ISO 10349-11-2002 | 摄影照相级化学品试验方法第11部分:比重的测定 | Photography-photographic-grade chemicals-Test methods-Part 11:Determination specific gravity |
KS M ISO 10349-12-2002 | 摄影照相级化学品试验方法第12部分:密度的测定 | Photography-Photographic-grade chemicals-Test methods-Part 12:Determination of density |
KS M ISO 10349-13-2002 | 摄影照相级化学品试验方法第13部分:pH值的测定 | Photography-Photographic-grade chemicals-Test methods-Part 13:Determination of pH |
KS M ISO 10349-2-2002 | 摄影照相级化学品试验方法第2部分:水不溶物的测定 | Photography-Photographic-grade chemicals-Test methods-Part 2:Determination of matter insoluble in water |
KS M ISO 10349-3-2002 | 摄影照相级化学品试验方法第3部分:氢氧化铵溶液不溶物的测定 | Photography-Photographic-grade chemicals-Test methods-Part 3:Determination of matter insoluble in ammonium hydroxide solution |
KS M ISO 10349-4-2002 | 摄影照相级化学品试验方法第4部分:灼烧残渣的测定 | Photography-Photographic-grade chemicals-Test methods-Part 4:Determination of residue after ignition |
KS M ISO 10349-5-2002 | 摄影照相级化学品试验方法第5部分:重金属和铁含量的测定 | Photography-Photographic-grade chemicals-Test methods-Part 5:Determination of heavy metals and iron content |
KS M ISO 10349-6-2002 | 摄影照相级化学品试验方法第6部分:卤化物含量的测定 | Photography-Photographic-grade chemicals-Test methods-Part 6:Determination of halide content |
KS M ISO 10349-7-2002 | 摄影照相级化学品试验方法第7部分:碱度或酸度的测定 | Photography-Photographic-grade chemicals-Test methods-Part 7:Determination of alkalinity or acidity |
KS M ISO 10349-8-2002 | 摄影照相级化学品试验方法第8部分:挥发物的测定 | Photography-Photographic-grade chemicals-Test methods-Part 8:Determination of volatile matter |
KS M ISO 10349-9-2002 | 摄影照相级化学品试验方法第9部分:与硝酸银氨的反应 | Photography-Photographic-grade chemicals-Test methods-Part 9:Reaction to ammoniacal silver nitrate |
KS M ISO 10350-1-2012 | 塑料可比单点数据的采集和表示第1部分:模塑材料 | Plastics-Acquisition and presentation of comparable single-point data-Part 1:Moulding materials |
KS M ISO 10350-2-2012 | 塑料可比单点数据的采集和表示第2部分:长纤维增强塑料 | Plastics-Acquisition and presentation of comparable single-point data-Part 2:Long-fibre-reinforced plastics |
KS M ISO 10352-2012 | 纤维增强塑料.模塑料和预浸料.单位面积质量的测定 | Fibre-reinforced plastics-Moulding compounds and prepregs-Determination of mass per unit area |
KS M ISO 10354-2004 | 粘合剂.结构粘合剂胶接组件间耐久特性.楔形破裂试验 | Adhesives-Characterization of durability of structural-adhesive-bonded assemblies-Wedge rupture test |
KS M ISO 10363-2009 | 热熔粘胶剂.热稳定性测定 | Hot-melt adhesives-Determination of thermal stability |
KS M ISO 10364-2004 | 粘合剂.多组分粘合剂的适用期的测定 | Adhesives-Determination of working life(pot life) of multi-component adhesives |
KS M ISO 10365-2004 | 粘合剂.主要断裂型式的命名 | Adhesives-Designation of main failure patterns |
KS M ISO 10366-2-2016 | 塑料甲基丙烯酸甲酯-丙烯腈-丁二烯-苯乙烯(MABS)模塑和挤塑材料第2部分:试样制备和性能测定 | Plastics-Methyl methacrylate-acrylonitrile-butadiene-styrene(MABS) moulding and extrusion materials-Part 2:Preparation of test specimens and determination of properties |
KS M ISO 10370-2017 | 石油产品残炭测定法(微量法) | Petroleum products-Determination of carbon residue-Micro method |
KS M ISO 10398-2007 | 橡胶硫化和未硫化物中促进剂的鉴别 | Rubber-Identification of accelerators in cured and uncured compounds |
KS M ISO 1043-1-2013 | 塑料符号和缩略语第1部分:基本聚合物及其特性 | Plastics — Symbols and abbreviated terms -- Part 1: Basic polymers and their special characteristics |
KS M ISO 1043-2-2013 | 塑料.符号和缩略语.第2部分:填料和增强材料 | Plastics — Symbols and abbreviated terms-Part 2: Fillers and reinforcing materials |
KS M ISO 1043-3-2003 | 塑料符号和缩略语第3部分:增塑剂 | Plastics-Symbols and abbreviated terms-Part 3 : Plasticizers |
KS M ISO 1043-4-2008 | 塑料符号和缩略语第4部分:阻燃剂 | Plastics-Symbols and abbreviated terms-Part 4:Flame retardants |
KS M ISO 10454-2007 | 载重汽车轮胎检验轮胎性能实验室试验方法 | Truck and bus tyres-Verifying tyre capabilities-Laboratory test methods |
KS M ISO 10466-2004 | 塑料管道系统.玻璃纤维增强热固性塑料(GRP)管材.耐初始环状变形可能性试验方法 | Plastics piping systems-Glass-reinforced thermosetting plastics(GRP) pipes-Test method to prove the resistance to initial ring deflection |
KS M ISO 10468-2004 | 玻璃增强热固性塑料(GRP)管.潮湿条件下长期特定环形蠕变硬度的测定和湿蠕变因子的计算 | Glass-reinforced thermosetting plastics(GRP) pipes-Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor |
KS M ISO 10471-2004 | 玻璃纤维增强热固塑料(GRP)管材在潮湿条件下长期极限弯曲应变和长期极限相对环挠度的测定 | Glass-reinforced thermosetting plastics(GRP) pipes-Determination of the long-term ultimate bending strain and long-term ultimate relative ring deflection under wet conditions |
KS M ISO 10478-2003 | 石油产品.中间燃份油中的铝和硅的测定.感应耦合等离子发射和原子吸收光谱法 | Petroleum products-Determination of aluminium and silicon in fuel oils-Inductively coupled plasma emission and atomic absorption spectroscopy methods |
KS M ISO 10499-1-2007 | 工业轮胎和轮辋-充气轮胎轮辋用实心轮胎(米制系列)-第1部分:名称、尺寸和标记 | Industrial tyres and rims-Solid tyres(metric series) for pneumatic tyre rims-Part 1:Designation, dimensions and marking |
KS M ISO 10499-2-2007 | 工业轮胎和轮辋-充气轮胎轮辋用橡胶实心轮胎(米制系列)-第2部分:额定载荷 | Industrial tyres and rims-Rubber solid tyres(metric series)for pneumatic tyre rims-Part 2:Load ratings |
KS M ISO 10500-2007 | 工业轮胎和轮辋圆柱和圆锥底橡胶实心轮胎(米制系列)-名称、尺寸和标志 | Industrial tyres and rims-Cylindrical and conical base rubber solid tyres(metric series)-Designation, dimensions and marking |
KS M ISO 10571-2017 | 移动式起重机和类似专用机械用轮胎 | Tyres for mobile cranes and similar specialized machines |
KS M ISO 1060-1-2002 | 塑料.氯乙烯的均聚物和共聚物树脂.第1部分:命名体系和基本规范 | Plastics-Homopolymer and copolymer resins of vinyl chloride-Part 1:Designation system and basis for specifications |
KS M ISO 10601-2012 | 涂料用云母氧化铁颜料规范和试验方法 | Micaceous iron oxide pigments for paints- Specifications and test methods |
KS M ISO 1060-2-2002 | 塑料氯乙烯均聚和共聚树脂第2部分:试样的制备和性能的测定 | Plastics-Homopolymer and copolymer resins of vinyl chloride-Part 2:Preparation of test samples and determination of properties |
KS M ISO 10619-1-2014 | 橡胶和塑料软管及管材柔性和刚度的测量第1部分:室温弯曲试验 | Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part1: Bending tests at ambient temperature |
KS M ISO 10619-2-2014 | 橡胶和塑料软管和管.柔性和刚度的测量.第2部分:低于环境温度的弯曲试验 | Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 2: Bending tests at sub-ambient temperatures |
KS M ISO 10619-3-2014 | 橡胶和塑料软管和管.柔性和刚度的测量.第3部分:高温和低温下的弯曲试验 | Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 3: Bending tests at high and low temperatures |
KS M ISO 1063-2006 | 表面活性剂硬水稳定性的测定 | Surface active agents-Determination of stability in hard water |
KS M ISO 10636-2002 | 摄影加工用化学品无水硫代硫酸钠和五水硫代硫酸钠规范 | Photography-Processing chemicals-Specifications for anhydrous sodium thiosulfate and sodium thiosulfate pentahydrate |
KS M ISO 10638-2012 | 橡胶防降解剂的气相色谱/质谱鉴定 | Rubber-Identification of antidegradants by gas chromatography/mass spectrometry |
KS M ISO 1064-2003 | 表面活性剂.浆状物在灌装时表观密度的测定 | Surface active agents-Determination of apparent density of pastes on filling |
KS M ISO 1065-2003 | 由环氧乙烷制得的非离子表面活性剂及混合非离子表面活性剂.浊点的测定 | Non-ionic surface-active agents obtained from ethylene oxide and mixed non-ionic surface-active agents-Determination of cloud point |
KS M ISO 1066-2003 | 肥皂的分析.甘油含量的测定.滴定法 | Analysis of soaps-Determination of glycerol content-Titrimetric method |
KS M ISO 1067-2003 | 肥皂分析方法不皂化、不皂化和不皂化皂化物的测定 | Analysis of soaps-Determination of unsaponifiable, unsaponified and unsaponified saponifiable matter |
KS M ISO 10716-2017 | 纸和纸板碱储量的测定 | Paper and board-Determination of alkali reserve |
KS M ISO 10718-2004 | 软木塞.可在酒类介质中生长的酵母、霉菌和细菌群落形成单位的计数 | Cork stoppers-Enumeration of colony-forming units of yeasts, moulds and bacteria capable of growth in an alcoholic medium |
KS M ISO 10724-1-2010 | 塑料热固粉末模塑化合物(PMCS)试样的注射成型第1部分:一般原理和多用途试样的成型 | Plastics-Injection moulding of test specimens of thermosetting powder moulding compounds(PMCs)-Part 1:General principles and moulding of multipurpose test specimens |
KS M ISO 10724-2-2010 | 塑料热固粉末模塑化合物(PMCS)试样的注射成型第2部分:小板 | Plastics-Injection moulding of test specimens of thermosetting powder moulding compounds(PMCs)-Part 2:Small plates |
KS M ISO 10775-2016 | 纸、纸板和纸浆镉含量的测定原子吸收光谱法 | Paper, board and pulps-Determination of cadmium content-Atomic absorption spectrometric method |
KS M ISO 10840-2013 | 塑料.标准燃烧试验的使用指南 | Plastics — Guidance for the use of standard fire tests |
KS M ISO 10890-2012 | 色漆和清漆防污漆中杀菌剂释放速率的质量平衡计算模型 | Paints and varnishes-Modelling of biocide release rate from antifouling paints by mass-balance calculation |
KS M ISO 10928-2004 | 塑料管道系统玻璃纤维增强热固塑料(GRP)管道及配件回归分析方法及其应用 | Plastics piping systems-Glass-reinforced thermosetting plastics(GRP) pipes and fittings-Methods for regression analysis and their use |
KS M ISO 10933-2009 | 气体分配系统用聚乙烯(PE)阀门 | Polyethylene(PE) valves for gas distribution systems |
KS M ISO 10952-2017 | 塑料管道系统玻璃纤维增强热固塑料(GRP)管材和管件弯曲状态下截面内耐化学侵蚀性的测定 | Plastics piping systems-Glass-reinforced thermosetting plastics (GRP) pipes and fittings-Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
KS M ISO 10960-2016 | 橡胶和塑料软管.动态条件下耐臭氧性的评定 | Rubber and plastics hoses-Assessment of ozone resistance under dynamic conditions |
KS M ISO 10964-2010 | 粘合剂.螺纹紧固件上厌氧粘合剂的抗扭强度的测定 | Adhesives-Determination of torque strength of anaerobic adhesives on threaded fasteners |
KS M ISO 11003-1-2010 | 胶粘剂结构胶粘剂剪切性能的测定第1部分:用对接连接空心圆筒的扭转试验方法 | Adhesives-Determination of shear behaviour of structural adhesives-Part 1:Torsion test method using butt-bonded hollow cylinders |
KS M ISO 11003-2-2010 | 胶粘剂结构胶粘剂剪切性能的测定第2部分:厚粘附体拉伸试验方法 | Adhesives-Determination of shear behaviour of structural adhesives-Part 2:Tensile test method using thick adherends |
KS M ISO 11007-2003 | 石油产品和润滑剂.润滑脂防锈性能的测定 | Petroleum products and lubricants-Determination of rust-prevention characteristics of lubricating greases |
KS M ISO 11009-2014 | 石油产品和润滑剂.润滑脂抗水淋特性的测定 | Petroleum products and lubricants — Determination of water washout characteristics of lubricating greases |
KS M ISO 11014-2017 | 化工产品安全数据表.章节内容和顺序 | Safety data sheet for chemical products — Content and order of sections |
KS M ISO 1104-2006 | 表面活性剂工业烷基芳基磺酸钠(苯衍生物除外)分析方法 | Surface active agents-Technical sodium alkylarylsulphonates(excluding benzene derivatives)-Methods of analysis |
KS M ISO 11089-2012 | 合成生胶.用高效液相色谱法测定防老剂 | Rubber, raw synthetic-Determination of antidegradants by high-performance liquid chromatography |
KS M ISO 11093-1-2008 | 纸和纸板.硬纸板锥形圆筒的检验.第1部分:取样 | Paper and board-Testing of cores-Part 1:Sampling |
KS M ISO 11093-2-2008 | 纸和纸板.硬纸板锥形圆筒的检验.第2部分:试样的处理 | Paper and board-Testing of cores-Part 2:Conditioning of test samples |
KS M ISO 11093-3-2008 | 纸和纸板.硬纸板锥形圆筒的检验.第3部分:用烘箱干燥法测定含水量 | Paper and board-Testing of cores-Part 3:Determination of moisture content using the oven drying method |
KS M ISO 11093-4-2008 | 纸和纸板.硬纸板锥形圆筒的检验.第4部分:尺寸测量 | Paper and board-Testing of cores-Part 4:Measurement of dimensions |
KS M ISO 11093-5-2014 | 纸和纸板.硬纸板锥形圆筒的检验.第5部分:同心旋转特性的测定 | Paper and board — Testing of cores — Part 5: Determination of characteristics of concentric rotation |
KS M ISO 11093-6-2016 | 纸和纸板.硬纸板锥形圆筒的检验.第6部分:用三点法测定弯曲强度 | Paper and board - Testing of cores - Part 6 : Determination of bending strength by the three-point method |
KS M ISO 11093-7-2014 | 纸和纸板.硬纸板锥形圆筒的检验.第7部分:用三点法测定弯曲模量 | Paper and board — Testing of cores — Part 7: Determination of flexural modulus by the three-point method |
KS M ISO 11093-8-2014 | 纸和纸板.硬纸板锥形圆筒的检验.第8部分:用试验模态分析法测定固有频率和弯曲模量 | Paper and board — Testing of cores — Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis |
KS M ISO 11093-9-2008 | 纸和纸板.硬纸板锥形圆筒的检验.第9部分:平压强度的测定 | Paper and board-Testing of cores-Part 9:Determination of flat crush resistance |
KS M ISO 11108-2014 | 信息和文献.档案纸.稳定耐久性的要求 | Information and documentation-Archival paper-Requirements for permanence and durability |
KS M ISO 11124-1-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料规范第1部分:一般介绍和分类 | Preparation of steel substrates before application of paints and related products-Specification for metallic blast-cleaning abrasives-Part 1:General introduction and classification |
KS M ISO 11124-2-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料规范第2部分:冷激铁砂 | Preparation of steel substrates before application of paints and related products-Specification for metallic blast-cleaning abrasives-Part 2:Chilled-iron grit |
KS M ISO 11124-3-2008 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料规范第3部分:高碳铸钢丸和砂 | Preparation of steel substrates before application of paints and related products-Specifications for metallic blast-cleaning abrasives-Part 3:High-carbon cast-steel shot and grit |
KS M ISO 11124-4-2003 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料规范第4部分:低碳铸钢丸 | Preparation of steel substrates before application of paints and related products-Specifications for metallic blast-cleaning abrasives-Part 4:Low-carbon cast-steel shot |
KS M ISO 11125-1-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料的试验方法第1部分:取样 | Preparation of steel substrates before application of paints and related products-Test methods for metallic blast-cleaning abrasives-Part 1:Sampling |
KS M ISO 11125-2-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料的试验方法第2部分:粒度分布的测定 | Preparation of steel substrates before application of paints and related products-Test methods for metallic blast-cleaning abrasives-Part 2 : Determination of particle size distribution |
KS M ISO 11125-3-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料的试验方法第3部分:硬度的测定 | Preparation of steel substrates before application of paints and related products-Test methods for metallic blast - cleaning abrasives-Part 3:Determination of hardness |
KS M ISO 11125-4-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料的试验方法第4部分:表观密度的测定 | Preparation of steel substrates before application of paints and related products-Test methods for metallic blast-cleaning abrasives-Part 4:Determination of apparent density |
KS M ISO 11125-5-2002 | 涂装油漆和有关产品前钢材预处理喷射清理用金属磨料的试验方法第5部分:缺陷颗粒百分比和微观结构的测定 | Preparation of steel substrates before application of paints and related products-Test methods for metallic blast-cleaning abrasives-Part 5:Determination of percentage defective particles and of microstructure |