KS M ISO 75-3-2013

塑料.载荷下挠曲温度的测定.第3部分：高强度热固层压板和长纤维增强塑料

Plastics — Determination of temperature of deflection under load–Part 3: High-strength thermosetting laminate and   long-fiber-reinforced plastics

KS M ISO 7535-2007

表面活性剂家用洗碗机用洗涤剂性能比较试验指南

Surface active agents－Detergents for domestic machine   dishwashing－Guide for comparative testing of   performance

KS M ISO 7536-2015

石油产品汽油氧化安定性测定诱导期法

Petroleum products－Determination of oxidation stability   of gasoline－Induction period method

KS M ISO 7537-2003

石油产品酸值测定半微量显色指示剂滴定法

Petroleum products－Determination of acid number－Semi-micro colour-indicator titration method

KS M ISO 7579-2012

染料在有机溶剂中溶解度的测定重量法和光度法

Dyestuffs ㅡ   Determination of solubility in organic solvents ㅡ Gravimetric and photometric methods

KS M ISO 758-2016

工业液体化工产品20℃密度的测定

Liquid chemical products for industrial use－Determination of density at 20 ℃

KS M ISO 759-2017

工业用挥发性有机液体水浴蒸发后干残渣的测定通用方法

Volatile organic liquids for industrial use   — Determination of dry   residue after evaporation on water bath — General   method

KS M ISO 760-2017

水的测定卡尔费休法（通用方法）

Determination of water — Karl Fischer method(General method)

KS M ISO 7616-2010

硬质泡沫塑料在规定载荷和温度条件下压缩蠕变的测定

Cellular plastics, rigid－Determination of compressive creep   under specified load and temperature conditions

KS M ISO 7619-1-2016

硫化橡胶或热塑性橡胶压痕硬度的测定第1部分：硬度计法（肖氏硬度）

Rubber, vulcanized or thermoplastic－Determination of indentation hardness－Part 1：Durometer method(Shore hardness)

KS M ISO 7619-2-2016

硫化橡胶或热塑性橡胶压痕硬度的测定第2部分：IRHD袖珍式硬度计法

Rubber, vulcanized or thermoplastic－Determination of indentation hardness－Part 2：IRHD pocket meter method

KS M ISO 7622-1-2002

钢丝绳芯输送带纵向牵引试验第1部分：伸长的测量

Steel cord conveyor belts－Longitudinal traction test－Part 1：Measurement of elongation

KS M ISO 7622-2-2002

钢丝绳芯输送带.纵向牵引力试验.第2部分:拉伸强度的测量

Steel cord conveyor belts－Longitudinal traction test－Part 2：Measurement of tensile strength

KS M ISO 7624-2003

石油产品和润滑剂.抑制矿物质涡轮机油.氧化稳定性的测定

Petroleum products and lubricants－Inhibited mineral turbine oils－Determination of oxidation stability

KS M ISO 765-2003

农药和其他农用化学品.通用名称

Pesticides considered not to require common   names

KS M ISO 7662-2003

橡胶和塑料管.内衬磨损的测定

Rubber and plastic hoses－Determination of abrasion of lining

KS M ISO 7663-2017

卤化异丁烯-异戊二烯橡胶(BIIR和CIIR).评价方法

Halogenated isobutene-isoprene rubber(BIIR   and CIIR) — Evaluation procedures

KS M ISO 7664-2007

天然生胶和合成生胶.存储通用指南

Rubber, raw natural and raw synthetic－General guidance on storage

KS M ISO 7682-2009

建筑内污、废水排放（低温、高温）塑料管道系统丙烯腈-丁二烯-苯乙烯（ABS）

Plastics piping systems for soil and waste   discharge(low and high temperature) inside buildings－Acrylonitrile-butadiene-styrene(ABS)

KS M ISO 7684-2004

玻璃纤维增强热固性塑料(GRP)管材.干燥条件下蠕变系数的测定

Plastics piping systems－Glass-reinforced thermosetting   plastics(GRP) pipes－Determination of the creep factor   under dry conditions

KS M ISO 7685-2004

玻璃纤维增强热固性塑料(GRP)管材.初始有效环刚度的测定

Plastics piping systems－Glass-reinforced thermosetting   plastics(GRP) pipes－Determination of initial specific   ring stiffness

KS M ISO 7686-2016

塑料管材和管件.不透明度.试验方法

Plastics pipes and fittings－Opacity－Test   method

KS M ISO 7724-1-2007

色漆和清漆.比色法.第1部分:原理

Paints and varnishes－Colorimetry－Part   1：Principles

KS M ISO 7724-2-2007

色漆和清漆比色法第2部分：颜色测量

Paints and varnishes－Colorimetry－Part   2：Colour measurement

KS M ISO 7724-3-2007

色漆和清漆比色法第3部分：色差的计算

Paints and varnishes－Colorimetry－Part   3：Calculation of color differences

KS M ISO 7743-2016

硫化或热塑性橡胶.压缩应力.应变性能测定

Rubber, vulcanized or thermoplastic－Determination of compression   stress-strain properties

KS M ISO 776-2017

纸浆.酸不溶灰分的测定

Pulps－Determination of acid-insoluble ash

KS M ISO 7765-1-2002

塑料膜和板.用自由落体法测定耐冲击性.第1部分:梯级法

Plastics film and sheeting－Determination of impact resistance by   the free－falling dart method－Part   1：Staircase methods

KS M ISO 7765-2-2002

塑料薄膜和薄片自由落体冲击试验方法第2部分：仪器化穿孔试验

Plastics film and sheeting－Determination of impact resistance by   the free－falling dart method－Part   2：Instrumented puncture test

KS M ISO 7780-2016

橡胶和橡胶胶乳.锰含量的测定.高碘酸钠光度法

Rubber and rubber latices－Determination of manganese content－Sodium periodate photometric methods

KS M ISO 7781-2016

丁苯生胶.皂类和有机酸含量的测定

Styrene-butadiene rubber, raw－Determination of soap and   organic-acid content

KS M ISO 7783-2017

色漆和清漆水蒸气透过性能的测定杯法

Paints and varnishes－Determination of water-vapour   transmission properties－Cup method

KS M ISO 7784-1-2017

色漆和清漆耐磨性的测定第1部分：旋转砂纸覆盖轮法

Paints and varnishes－Determination of resistance to   abrasion－Part 1：Rotating   abrasive-paper-covered wheel method

KS M ISO 7784-2-2017

色漆和清漆耐磨性的测定第2部分：旋转磨橡胶轮法

Paints and varnishes－Determination of resistance to   abrasion－Part 2：Rotating   abrasive rubber wheel method

KS M ISO 7784-3-2017

色漆和清漆耐磨性的测定第3部分：往复试验板法

Paints and varnishes－Determination of resistance to   abrasion－Part 3：Reciprocating   test panel method

KS M ISO 7792-1-2013

塑料热塑性聚酯（TP）模塑和挤塑材料第1部分：命名系统和基本规范

Plastics ㅡ   Thermoplastic polyester(TP) moulding and extrusion materials ㅡ Part 1: Designation system and basis for   specifications

KS M ISO 7792-2-2013

塑料热塑性聚酯（TP）模塑和挤塑材料第2部分：试样制备和性能测定

Plastics ㅡ   Thermoplastic polyester(TP) moulding and extrusion materials ㅡ Part 2: Preparation of test specimens and   determination of properties

KS M ISO 78-2-2016

化学标准的格式.化学分析方法

Chemistry－Layouts for standards－Part 2：Method of chemical analysis

KS M ISO 7822-2002

玻璃纤维增强塑料.孔隙率的测定.烧失量、机械粉碎和静态计数法

Textile glass reinforced plastics－Determination of void content－Loss on ignition, mechanical disintegration and statistical   counting methods

KS M ISO 7823-1-2016

塑料－聚甲基丙烯酸甲酯片材－类型、尺寸和特性－第1部分：浇注片材

Plastics－Poly(methyl methacrylate) sheets－Types,   dimensions and characteristics－Part 1：Cast sheets

KS M ISO 7823-2-2014

塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第2部分：挤压板材

Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics —   Part 2: Extruded sheets

KS M ISO 7823-3-2014

塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第3部分：连续铸造板材

Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics —   Part 3: Continuous cast sheets

KS M ISO 78-3-2010

化学标准的格式.化学分析方法

Chemistry－Layouts for standards－Part 3：Standard for molecular absorption spectrometry

KS M ISO 78-4-2010

化学标准的格式.化学分析方法

Layouts for standards－Part 4：Standard   for atomic absorption spectrometric analysis

KS M ISO 7850-2010

硬质泡沫塑料.压缩蠕变的测

Cellular plastics, rigid－Determination of compressive creep

KS M ISO 7851-2017

肥料和土壤调理剂

Fertilizers and soil conditioners－Classification

KS M ISO 7867-1-2010

农业拖拉机和机械用轮胎和轮辋（米制系列）－第1部分：轮胎的名称、尺寸、标记和轮胎/轮辋的协调

Tyres and rims(metric series) for   agricultural tractors and machines－Part 1：Tyre designation,dimensions,marking   and tyre/rim coordination

KS M ISO 7867-2-2009

农业拖拉机和机械用轮胎和轮辋（米制系列）.第2部分：使用说明和额定载荷

Tyres and rims(metric series) for   agricultural tractors and machines－Part 2：Service description and load   ratings

KS M ISO 787-1

颜料和体质颜料的通用试验方法第1部分：颜料颜色的比较

General methods of test for pigments and   extenders－Part 1：Comparison of colour of pigments

KS M ISO 787-10-2007

颜料和体质颜料通用试验方法第10部分：密度的测定比重瓶法

General methods of test for pigments and   extenders－Part 10：Determination of density－Pyknometer method

KS M ISO 787-11-2007

颜料和体质颜料的通用试验方法第11部分：压实后压实体积和表观密度的测定

General methods of test for pigments and   extenders－Part 11：Determination of tamped volume and apparent density after tamping

KS M ISO 787-13-2012

颜料和体质颜料的通用试验方法第13部分：水溶性硫酸盐、氯化物和硝酸盐的测定

General methods of test for pigments and   extenders－Part 13：Determination of water-soluble sulfates, chlorides and nitrates

KS M ISO 787-14-2012

颜料和体质颜料通用试验方法第14部分：水萃取物电阻率的测定

General methods of test for pigments and   extenders－Part 14：Determination of resistivity of aqueous extract

KS M ISO 787-15-2007

颜料和体质颜料的通用试验方法第15部分：同类着色颜料耐光性的比较

General methods of test for pigments and   extenders－Part 15：Comparison of resistance to light of coloured pigments of similar   types

KS M ISO 787-16-2007

颜料和体质颜料的通用试验方法第16部分：相对着色力（或等效着色值）和着色颜料还原后颜色的测定目视比较法

General methods of test for pigments and   extenders－Part 16：Determination of relative tinting strength (or equivalent   colouring value) and colour on reduction of coloured pigments－Visual comparison method

KS M ISO 787-17-2012

颜料和体质颜料的通用试验方法第17部分：白色颜料消光力的比较

General methods of test for pigments and   extenders－Part 17：Comparison of lightening power of white pigments

KS M ISO 787-18-2007

颜料和体质颜料的通用试验方法第18部分：筛余物的测定机械冲洗法

General methods of test for pigments and   extenders－Part 18：Determination of residue on sieve－Mechanical   flushing procedure

KS M ISO 787-19-2007

颜料通用试验方法第19部分：水溶性硝酸盐的测定（水杨酸法）

General methods of test for pigments－Part 19：Determination   of water－soluble nitrates (Salicylic acid method)

KS M ISO 787-2

颜料和体质颜料的通用试验方法第2部分：105℃挥发物的测定

General methods of test for pigments and   extenders－Part 2：Determination of matter volatile at 105 degree C

KS M ISO 787-21-2007

颜料和体质颜料的通用试验方法第21部分：用烘干介质比较颜料的热稳定性

General methods of test for pigments and   extenders－Part 21：Comparison of heat stability of pigments using a stoving medium

KS M ISO 787-22-2007

颜料和体质颜料的通用试验方法第22部分：颜料抗渗色性的比较

General methods of test for pigments and   extenders－Part 22：Comparison of resistance to bleeding of pigments

KS M ISO 787-23-2007

颜料和体质颜料的通用试验方法第23部分：密度的测定（用离心机除去夹带的空气）

General methods of test for pigments and   extenders－Part 23：Determination of density (using a centrifuge to remove entrained   air)

KS M ISO 787-24-2007

颜料和体质颜料的通用试验方法第24部分：着色颜料相对着色力和白色颜料相对散射力的测定光度法

General methods of test for pigments and   extenders－Part 24：Determination of relative tinting strength of coloured pigments   and relative scattering power of white pigments－Photometric   methods

KS M ISO 787-25-2007

颜料和体质颜料的通用试验方法第25部分：白色、黑色和着色颜料在全荫系统中颜色的比较比色法

General methods of test for pigments and   extenders－Part 25：Comparison of the colour, in full－shade   systems,of white, black and coloured pigments－Colorimetric   method

KS M ISO 787-3

颜料和体质颜料的通用试验方法第3部分：水溶物的测定热萃取法

General methods of test for pigments and   extenders－Part 3：Determination of matter soluble in water－Hot   extraction method

KS M ISO 787-4

颜料和体质颜料的通用试验方法第4部分：水萃取物酸度或碱度的测定

General methods of test for pigments and   extenders－Part 4：Determination of acidity or alkalinity of the aqueous extract

KS M ISO 787-5

颜料和体质颜料通用试验方法第5部分：吸油值的测定

General methods of test for pigments and   extenders－Part 5：Determination of oil absorption value

KS M ISO 787-7

颜料和体质颜料的通用试验方法第7部分：筛余物的测定水法手工法

General methods of test for pigments and   extenders－Part 7：Determination of residue on sieve－Water   method－Manual procedure

KS M ISO 787-8

颜料和体质颜料通用试验方法第8部分：水溶物的测定冷萃取法

General methods of test for pigments and   extenders－Part 8：Determination of matter soluble in water－Cold   extraction method

KS M ISO 787-9

颜料和体质颜料的通用试验方法第9部分：水悬浮液pH值的测定

General methods of test for pigments and   extenders－Part 9：Determination of pH value of an aqueous suspension

KS M ISO 788-2013

色漆用群青颜料

Ultramarine pigments for paints

KS M ISO 7941-2003

工业丙烷和丁烷.气相色谱分析法

Commercial propane and butane－Analysis by gas chromatography

KS M ISO 8004-2003

铝生产用碳素材料.煅烧焦和煅烧碳产品.二甲苯密度的测定.比重瓶法

Carbonaceous materials for the production   of aluminium－Calcined coke and   calcined carbon products－Determination of the density   in xylene－Pyknometric method

KS M ISO 8008-2003

主要用于铝生产的氧化铝.吸附氮的比表面面积的测定.单点法

Aluminium oxide primarily used for the   production of aluminium－Determination   of specific surface area by nitrogen adsorption－Single-point   method

KS M ISO 8009-2013

机械避孕药可重复使用的天然和硅橡胶避孕子宫帽要求和试验

Mechanical contraceptives－Reusable natural and silicone rubber   contraceptive diaphragms－Requirements and tests

KS M ISO 801-1

纸浆成批销售质量的测定第1部分：片状包装纸浆

Pulps－Determination of saleable mass in lots－Part   1：Pulps baled in sheet form

KS M ISO 801-2

纸浆成批销售质量的测定第2部分：板包纸浆（如快干纸浆）

Pulps－Determination of saleable mass in lots－Part   2：Pulps(such as flash-dried pulps) baled in slabs

KS M ISO 801-3

纸浆成批销售质量的测定第3部分：整包

Pulps－Determination of saleable mass in lots－Part   3：Unitized bales

KS M ISO 8013-2016

硫化橡胶.压缩或剪切状态下的蠕变性能测定

Rubber, vulcanized－Determination of creep in compression   or shear

KS M ISO 8022-2003

表面活性剂.用浸没法测定润湿力

Surface active agents－Determination of wetting power by   immersion

KS M ISO 8028-2016

真空喷涂漆用橡胶和/或塑料软管和软管组件.规范

Rubber and/or plastics hoses and hose   assemblies for airless paint spraying－Specification

KS M ISO 8030-2008

橡胶和塑料软管可燃性试验方法

Rubber and plastics hoses－Method of test for flammability

KS M ISO 8031-2008

橡胶和塑料软管和软管组件.电阻率测定

Rubber and plastics hoses and hose   assemblies－Determination of   electrical resistance

KS M ISO 8032-2009

橡胶和塑料软管组件.液压脉冲弯曲试验(半Ω型试验),

Rubber and plastics hose assemblies－Flexing combined with hydraulic   impulse test(half-omega test)

KS M ISO 8033-2008

橡胶和塑料软管零部件间粘合强度的测定

Rubber and plastics hoses－Determination of adhesion between   components

KS M ISO 804-2003

主要用于铝生产的氧化铝分析用溶液的制备.碱熔化法

Aluminium oxide primarily used for the   production of aluminium－Preparation   of solution for analysis－Method by alkaline fusion

KS M ISO 805-2003

主要用于铝生产的氧化铝铁含量的测定.1,10-菲罗啉光度法

Aluminium oxide primarily used for the   production of aluminium－Determination   of iron content－1,10-phenantroline photometric method

KS M ISO 8053-2014

橡胶和乳胶.铜含量的测定.橡胶和乳胶.铜含量的测定-

Rubber and latex — Determination of copper content — Rubber and latex — Determination of   copper content —

KS M ISO 8067-2008

软质泡沫聚合物材料.撕裂强度测定

Flexible cellular polymeric materials－Determination of tear strength

KS M ISO 8068-2016

润滑剂、工业用油及有关产品（L类）－T系列（涡轮机）－涡轮机用润滑油规范

Lubricants, industrial oils and related   products(class L)－Family   T(Turbines)－Specification for lubricating oils for   turbines

KS M ISO 8085-1-2002

燃气用聚乙烯管件.第1部分:热熔承插连接管件

Polyethylene fittings for use with   polyethylene pipes for the supply of gaseous fuels－Metric series－Specifications－Part 1：Fittings for socket fusion using heated tools

KS M ISO 8085-2-2016

与供应气体燃料的聚乙烯饼一起使用的聚乙烯配件.米制系列.规范.第2部分：热熔接、热熔接和电熔接配件用套管配件

Polyethylene fittings for use with   polyethylene pies for the supply of gaseous fuels－Metric series－Specifications－Part 2：Spigot fittings for butt fusion, for socket fusion using heated   tools and for use with electrofusion fittings

KS M ISO 8085-3-2016

与供应气体燃料的聚乙烯管一起使用的聚乙烯配件.米制系列.规范.第3部分：电熔配件

Polyethylene fittings for use with   polyethylene pipes for the supply of gaseous fuels－Metric series－Specifications－Part 3：Electrofusion fittings

KS M ISO 8096-2009

防水布用橡胶或塑料涂层织物规范

Rubber- or plastics-coated fabrics for   water-resistant clothing－Specification

KS M ISO 8112-2008

工业用己内酰胺50%己内酰胺水溶液色度的测定(用哈森单位表示)(铂-钴标度).分光光度法

Caprolactam for industrial use－Determination of colour of 50 %   aqueous caprolactam solution, expressed in Hazen units(platinum-cobalt scale)－Spectrometric method

KS M ISO 812-2014

硫化橡胶或热塑性橡胶低温脆性的测定

Rubber, vulcanized or thermoplastic — Determination of low-temperature   brittleness

KS M ISO 8130-1-2008

粉末涂料第1部分：用筛分法测定粒度分布

Coating powders－Part 1：Determination   of particle size distribution by sieving

KS M ISO 8130-10

粉末涂料第10部分：沉积效率的测定

Coating powders－Part 10：Determination   of deposition efficiency

KS M ISO 8130-11

粉末涂料第11部分：斜面流动试验

Coating powders－Part 11：Inclined-plane   flow test

KS M ISO 8130-12

粉末涂料第12部分：相容性的测定

Coating powders－Part 12：Determination   of compatibility

KS M ISO 8130-13

粉末涂料第13部分：激光衍射粒度分析

Coating powders－Part 13：Particle   size analysis by laser diffraction

KS M ISO 8130-14

粉末涂料第14部分：术语

Coating powders－Part 14：Terminology

KS M ISO 8130-2-2008

粉末涂料第2部分：气体比较比重瓶法测定密度（仲裁法）

Coating powders－Part 2：Determination   of density by gas comparison pyknometer(referee method)

KS M ISO 8130-3-2009

粉末涂料第3部分：液体置换比重瓶法测定密度

Coating powders－Part 3：Determination   of density by liquid displacement pyknometer

KS M ISO 8130-4-2008

粉末涂料第4部分：爆炸下限的计算

Coating powders－Part 4：Calculation   of lower explosion limit

KS M ISO 8130-5-2008

粉末涂料第5部分：粉末/空气混合物流动性能的测定

Coating powders－Part 5：Determination   of flow properties of a powder/air mixture

KS M ISO 8130-6-2016

涂层粉末.第6部分：在给定温度下热固性涂层粉末的凝胶时间的测定

Coating powders－Part 6：Determination   of gel time of thermosetting coating powders at a given temperature

KS M ISO 8130-7-2008

粉末涂料第7部分：烘烤质量损失的测定

Coating powders－Part 7：Determination   of loss of mass on stoving

KS M ISO 8130-8-2008

粉末涂料第8部分：热固粉末贮存稳定性的评定

Coating powders－Part 8：Assessment   of the storage stability of thermosetting powders

KS M ISO 8130-9-2008

粉末涂料第9部分：取样

Coating powders－Part 9：Sampling

KS M ISO 813-2014

硫化或热塑性橡胶.与刚性粘合强度的测定.90°剥离法

Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid   substrate — 90˚ peel method

KS M ISO 814-2014

硫化橡胶或热塑性橡胶与金属粘合强度的测定双板法

Rubber, vulcanized or thermoplastic — Determination of adhesion to metal — Two-plate method

KS M ISO 815-1

硫化橡胶或热塑性橡胶压缩永久变形的测定第1部分：室温或高温下

Rubber, vulcanized or thermoplastic－Determination of compression set－Part 1：At ambient or elevated temperatures

KS M ISO 815-2

硫化橡胶或热塑性橡胶压缩永久变形的测定第2部分：低温下

Rubber, vulcanized or thermoplastic－Determination of compression set－Part 2：At low temperatures

KS M ISO 8157-2017

肥料和土壤调理剂.词汇

Fertilizers and soil conditioners－Vocabulary

KS M ISO 8174-2017

工业用乙烯和丙烯.丙酮、乙腈、二丙醇和甲醇的测定.气相色谱法

Ethylene and propylene for industrial use — Determination of acetone,   acetonitrile, propan-2-ol and methanol — Gas   chromatographic method

KS M ISO 8212-2003

肥皂和洗涤剂.生产过程中的取样技术

Soaps and detergents－Techniques of sampling during   manufacture

KS M ISO 8213-2016

工业用化学取样技术.从粉末到粗粒的粒状固体化学制品

Chemical products for industrial use－Sampling techniques－Solid chemical products in the form of particles varying from   powders to coarse lumps

KS M ISO 8214-2007

表面活性剂.洗衣粉.无机硫酸盐的测定.重量法

Surface active agents－Washing powders－Determination of inorganic sulfates－Gravimetric   method

KS M ISO 8215-2007

表面活性剂.洗衣粉.总二氧化硅含量的测定.重量法

Surface active agents－Washing powders－Determination of total silica content－Gravimetric   method

KS M ISO 8216-1-2011

石油产品燃料（F类）分类第1部分：船用燃料分类

Petroleum products－Fuels(class F) classification－Part 1：Categories of marine fuels

KS M ISO 8216-2-2003

石油产品燃料（F类）分类第2部分：工业和船舶用燃气轮机燃料分类

Petroleum products－Fuels(class F)－Classification－Part 2：Categories of gas turbine fuels for industrial and marine   applications

KS M ISO 8216-3-2003

石油产品燃料（F类）分类第3部分：L组（液化石油气）

Petroleum products－Fuels(class F)－Classification－Part 3：Family L(Liquefied petroleum gases)

KS M ISO 8216-99

石油产品燃料分类第99部分：总则

Petroleum products－Fuels(class F)－Classification－Part 99：General

KS M ISO 8217-2013

石油产品燃料（F类）船用燃料规范

Petroleum products ㅡFuels(class F) ㅡSpecification   of marine fuels

KS M ISO 8220-2003

主要用于铝生产的氧化铝.微晶粒(小于60毫微米筛目)大小分布的测定.电沉积筛分法

Aluminium oxide primarily used for the   production of aluminium-Determination of the fine particle size distribution   (less than 60 ㎛)-Method using electroformed sieves

KS M ISO 8226-1-2008

纸和纸板.湿膨胀性的测量.第1部分：最大相对湿度为68%的湿膨胀性

Paper and board－Measurement of hygroexpansivity－Part 1：Hygroexpansivity up to a maximum   relative humidity of 68 %

KS M ISO 8226-2-2008

纸和纸板.湿膨胀性的测量.第2部分：最大相对湿度为86%的湿膨胀性

Paper and board－Measurement of hygroexpansivity－Part 2：Hygroexpansivity up to a maximum   relative humidity of 86 %

KS M ISO 8254-1-2009

纸和纸板镜面光泽度的测量第1部分：会聚束75°光泽度的Tappi法

Paper and board－Measurement of specular gloss－ Part 1：75° gloss   with a converging beam, TAPPI method

KS M ISO 8254-2-2004

纸和纸板镜面光泽度的测量第2部分：平行光束75°光泽度，DIN法

Paper and board－Measurement of specular gloss－Part 2：75 ° gloss   with a parallel beam, DIN method

KS M ISO 8254-3-2016

纸和纸板镜面光泽度的测量第3部分：会聚束20度光泽度的Tappi法

Paper and board－Measurement of specular gloss－Part 3：20 degree gloss with a converging   beam, TAPPI method

KS M ISO 8256-2012

塑料拉伸冲击强度的测定

Plastics－Determination of tensile-impact strength

KS M ISO 8257-1-2002

塑料聚甲基丙烯酸甲酯模塑和挤塑材料第1部分：命名系统和基本规范

Plastics－Poly(methylmethacrylate) moulding and extrusion materials－Part 1：Designation system and basis for   specifications

KS M ISO 8257-2-2002

塑料聚甲基丙烯酸甲酯（PMMA）模塑和挤塑材料第2部分：试样制备和性能测定

Plastics－Poly(methyl methacrylate) (PMMA) moulding and extrusion materials－Part 2：Preparation of test specimens and   determination of properties

KS M ISO 8295-2016

塑料.薄膜和薄板.摩擦系数的测定

Plastics－Film and sheeting－Determination of the   coefficients of friction

KS M ISO 8296-2012

塑料.薄膜和薄板.湿润表面张力的测定

Plastics－Film and sheeting－Determination of wetting   tension

KS M ISO 8307-2008

软质泡沫聚合材料球回弹法测定弹性

Flexible cellular polymeric materials－Determination of resilience by ball   rebound

KS M ISO 8308-2008

橡胶和塑料软管和管材液体通过软管和管材壁的传输测定

Rubber and plastics hoses and tubing－Determination of transmission of   liquids through hose and tubing walls

KS M ISO 8330-2009

橡胶和塑料软管及软管组件.词汇

Rubber and plastics hoses and hose   assemblies－Vocabulary

KS M ISO 8331-2009

橡胶和塑料软管和软管组件——_，_，国际_____

Rubber and plastics hoses and hose   assemblies－ 선택, 저장, 사용 및 유지에 대한 안내서

KS M ISO 844-2017

硬质泡沫塑料.压缩特性的测定

Rigid cellular plastics－Determination of compression   properties

KS M ISO 845-2012

泡沫塑料和橡胶.表观密度的测定

Cellular plastics and rubbers－Determination of apparent density

KS M ISO 846-2014

塑料对微生物作用评价

Plastics — Evaluation of the action of microorganisms

KS M ISO 8483-2004

玻璃增强热固性塑料管及配件.栓结法兰接头设计验证的试验方法

Glass-reinforced thermosetting   plastics(GRP) pipes and fittings－Test methods to prove the design of bolted flange joints

KS M ISO 8501-1-2013

涂装油漆和有关产品前钢材预处理表面清洁度评定试验第1部分：可溶性铁腐蚀产品的现场试验

Preparation of steel substrates before   application of paints and related products ㅡTests   for the assessment of surface cleanliness ㅡPart   1: Field test for soluble iron corrosion products

KS M ISO 8501-2-2008

涂装油漆和有关产品前钢材预处理表面清洁度的目视评定第2部分：局部清除原有涂层后钢材预处理等级

Preparation of steel substrates before   application of paints and related products－Visual assessment of surface cleanliness－Part   2：Preparation grades of previously coated steel   substrates after localized removal of previous coatings

KS M ISO 8501-3-2008

涂装油漆和有关产品前钢材预处理表面清洁度的目视评定第3部分：焊缝、切边和其他有表面缺陷区域的预处理等级

Preparation of steel substrates before   application of paints and related products－Visual assessment of surface cleanliness－Part   3：Preparation grades of welds,cut edges and other   areas with surface imperfections

KS M ISO 8502-11

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第11部分：水溶性硫酸盐的现场比浊测定法

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 11：Field method for the turbidimetric   determination of water-soluble sulfate

KS M ISO 6721-10-2016

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第12部分：水溶性亚铁离子的现场滴定测定法

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 12：Field method for the titrimetric   determination of water-soluble ferrous ions

KS M ISO 8502-2-2017

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第2部分：清洁表面氯化物的实验室测定

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 2：Laboratory determination of   chloride on cleaned surfaces

KS M ISO 8502-3-2017

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第3部分：涂装前钢材表面粉尘的评定（压敏胶带法）

Preparation of steel substrates before   application of paint and related products－Tests for the assessment of surface cleanliness－Part 3：Assessment of dust on steel surface   prepared for painting (pressure-sensitive tape method)

KS M ISO 8502-4-2017

涂料和有关产品使用前钢衬底的制备.表面清洁度的评定试验.第4部分：涂料使用前冷凝可能性的评定指南

Preparation of steel substrates before   application of paints and related products — Tests for the assessment of surface cleanliness — Part 4: Guidance on the estimation of the probability of   condensation prior to paint application

KS M ISO 8502-5-2002

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第5部分：涂装前钢材表面氯化物的测定（离子检测管法）

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 5：Measurement of chloride on steel   surfaces prepared for painting (ion detection tube method)

KS M ISO 8502-6-2012

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第6部分：分析用可溶性污染物的提取Bresle法

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 6：Extraction of soluble contaminants   for analysis－The Bresle method

KS M ISO 8502-9-2002

涂装油漆和有关产品前钢材预处理表面清洁度的评定试验第9部分：水溶性盐的现场电导测定法

Preparation of steel substrates before   application of paints and related products－Tests for the assessment of surface cleanliness－Part 9：Field method for the conductometric   determination of water-soluble salts

KS M ISO 8503-1-2012

涂装油漆和有关产品前钢材预处理喷射清理钢材的表面粗糙度特性第1部分：磨料喷射清理表面评定用ISO表面轮廓比较仪的规范和定义

Preparation of steel substrates before   application of paints and related products－Surface roughness characteristics of blast-cleaned steel   substrates－Part 1：Specifications   and definitions for ISO surface profile comparators for the assessment of   abrasive blast-cleaned surfaces

KS M ISO 8503-2-2012

涂装油漆和有关产品前钢材预处理喷射清理钢材的表面粗糙度特性第2部分：磨料喷射清理钢材表面轮廓的分级方法比较法

Preparation of steel substrates before   application of paints and related products－Surface roughness characteristics of blast-cleaned steel   substrates－Part 2：Method for   the grading of surface profile of abrasive blast-cleaned steel－Comparator procedure

KS M ISO 8503-3-2012

涂装油漆和有关产品前钢材预处理喷射清理钢材的表面粗糙度特性第3部分：ISO表面轮廓比较仪的校准方法和表面轮廓的测定聚焦显微镜法

Preparation of steel substrates before   application of paints and related products－Surface roughness characteristics of blast-cleaned steel   substrates－Part 3：Method for the   calibration of ISO surface profile comparators and for the determination of   surface profile－Focusing microscope procedure

KS M ISO 8503-4-2012

涂装油漆和有关产品前钢材预处理喷射清理钢材的表面粗糙度特性第4部分：ISO表面轮廓比较仪的校准方法和表面轮廓的测定触针法

Preparation of steel substrates before   application of paints and related products－Surface roughness characteristics of blast-cleaned steel   substrates－Part 4：Method for   the calibration of ISO surface profile comparators and for the determination   of surface profile－Stylus instrument procedure

KS M ISO 8503-5-2011

涂装油漆和有关产品前钢材预处理喷射清理钢材的表面粗糙度特性第5部分：表面轮廓测定的复制带法

Preparation of steel substrates before   application of paints and related products－Surface roughness characteristics of blast-cleaned steel substrates－Part 5：Replica tape method for the   determination of the surface profile

KS M ISO 8504-1-2012

涂装油漆和有关产品前钢材预处理表面预处理方法第1部分：总则

Preparation of steel substrates before   application of paints and related products－Surface preparation methods－Part 1：General principles

KS M ISO 8504-2-2012

涂装油漆和有关产品前钢材预处理表面预处理方法第2部分：喷砂清理

Preparation of steel substrates before   application of paints and related products－Surface preparation methods－Part 2：Abrasive blast-cleaning

KS M ISO 8504-3-2002

涂装油漆和有关产品前钢材预处理表面预处理方法第3部分：手工和电动工具清理

Preparation of steel substrates before   application of paints and related products－Surface preparation methods－Part 3：Hand- and power-tool cleaning

KS M ISO 8507-2004

集成软木盘.试验方法

Agglomerated cork discs－Test methods

KS M ISO 8510-2-2012

胶粘剂与刚性试验样品组件的剥离试验第2部分：180°剥离

Adhesives－Peel test for a flexible-bonded-to-rigid test specimen   assembly－Part 2：180° peel

KS M ISO 8511-2007

橡胶配合剂.炭黑.粒径分布的测定

Rubber compounding ingredients－Carbon black－Determination   of pellet size distribution

KS M ISO 8513-2017

玻璃纤维增强热固性塑料(GRP)管材.纵向抗拉特性的测定

Plastics piping systems — Glass-reinforced thermosetting   plastics(GRP) pipes — Test methods for the   determination of the apparent initial longitudinal tensile strength

KS M ISO 8516-2011

纺织玻璃纤维.膨体纱.基本规范

Textile glass－Textured yarns－Basis for a   specification

KS M ISO 8521-2004

玻璃纤维增强热固性塑料(GRP)管材.表面内周拉伸强度的测定

Plastics piping systems－Glass-reinforced thermosetting   plastics(GRP) pipes－Determination of the apparent   initial circumferential tensile strength

KS M ISO 8533-2004

玻璃纤维增强热固性塑料(GRP)管材.胶合接头或包好的接头设计验证的试验方法

Glass-reinforced thermosetting   plastics(GRP) pipes and fittings－Test methods to prove the design of cemented or wrapped joints

KS M ISO 8570-2014

塑料.薄膜和薄板.冷裂温度的测定

Plastics — Films and sheeting —   Determination of cold-crack temperature

KS M ISO 8604-2003

塑料.预浸料.术语定义和命名符号

Plastics－Prepregs－Definitions of terms and symbols   for designations

KS M ISO 8605-2016

玻璃纤维增强塑料片状模塑料(SMC).基本规范

Textile-glass-reinforced plastics－Sheet moulding compound(SMC)－Basis for a specification

KS M ISO 8606-2006

塑料.预浸料.整体模塑料(BMC)和团状模塑料(DMC).基本规范

Plastics－Prepregs－Bulk moulding compound(BMC) and   dough moulding compound(DMC)－Basis for a   specification

KS M ISO 862-2014

表面活性剂.词汇

Surface active agents — Vocabulary

KS M ISO 8623-2016

色漆和清漆用松焦油脂肪酸.规范和试验方法

Tall-oil fatty acids for paints and   varnishes－Specifications and   test methods

KS M ISO 8658-2003

铝生产用碳素材料.未煅烧和煅烧焦.火焰原子吸收光谱法测定痕量元素

Carbonaceous materials for use in the   production of aluminium－Green   and calcined coke－Determination of trace elements by   flame atomic absorption spectroscopy

KS M ISO 8660-2007

塑料己内酰胺高锰酸盐吸收值的测定分光光度法

Plastics－Determination of permanganate absorption number of caprolactam－Spectrometric method

KS M ISO 8661-2007

工业用己内酰胺.挥发性碱含量的测定.蒸馏后滴定法

Carprolactam for industrial use－Determination of volatile bases   content－Titrimetric method after distillation

KS M ISO 8664-2012

农业拖拉机和机械用轮胎.标定规定名称和使用条件的径向驱动轮轮胎

Tyres for agricultural tractors and   machines－Code-designated and   service-description marked radial drive-wheel tyres

KS M ISO 8681-2003

石油产品和润滑剂.分类法.等级的定义

Petroleum products and lubricants－Method of classification－Definition of classes

KS M ISO 868-2016

塑料和硬质橡胶用硬度计测定压痕硬度（肖氏硬度）

Plastics and ebonite－Determination of indentation hardness   by means of a durometer(Shore hardness)

KS M ISO 8697-2003

原油和石油产品.运输量估算.船上质量(OBQ)和船上剩余量(ROB)的评估

Crude petroleum and petroleum products－Transfer accountability－Assessment of on board quantity(OBQ) and quantity remaining on   board(ROB)

KS M ISO 871-2014

塑料.用热风炉测定点火温度

Plastics — Determination of ignition temperature using a hot-air   furnace

KS M ISO 8723-2004

铝生产用碳素材料.煅烧焦.油含量的测定.溶剂萃取法

Carbonaceous materials for the production   of aluminium－Calcined coke－Determination of oil content－Method by   solvent extraction

KS M ISO 8724-2016

软木装饰板.规范

Cork decorative panels－Specification

KS M ISO 8754-2016

石油产品.硫含量的测定.能量分散X射线荧光光谱测定法

Petroleum products－Determination of sulfur content－Energy dispersive X－ray fluorescence   method

KS M ISO 877-1

塑料太阳辐射暴露方法第1部分：通用指南

Plastics－Methods of exposure to solar radiation－Part   1：General guidance

KS M ISO 877-2

塑料太阳辐射曝露方法第2部分：窗玻璃后直接曝露和风化

Plastics－Methods of exposure to solar radiation－Part   2：Direct weathering and exposure behind window glass

KS M ISO 877-3

塑料太阳辐射暴露方法第3部分：集中太阳辐射强化风化

Plastics－Methods of exposure to solar radiation－Part   3：Intensified weathering using concentrated solar   radiation

KS M ISO 8779-2013

聚乙烯灌溉支管.规范

Polyethylene (PE) pipes for irrigation   laterals — Specifications

KS M ISO 8780-1-2002

颜料和体质颜料评定分散性的分散方法第1部分：引言

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 1：Introduction

KS M ISO 8780-2-2007

颜料和体质颜料评定分散性的分散方法第2部分：用振荡机分散

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 2：Dispersion using an oscillatory shaking machine

KS M ISO 8780-3-2007

颜料和体质颜料评定分散性的分散方法第3部分：用高速叶轮磨分散

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 3：Dispersion using a high-speed impeller mill

KS M ISO 8780-4-2007

颜料和体质颜料评定分散性的分散方法第4部分：用压片机分散

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 4：Dispersion using a bead mill

KS M ISO 8780-5-2007

颜料和体质颜料评定分散性的分散方法第5部分：用自动研磨机分散

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 5：Dispersion using an automatic muller

KS M ISO 8780-6-2007

颜料和体质颜料评定分散性的分散方法第6部分：用三辊磨分散

Pigments and extenders－Methods of dispersion for assessment   of dispersion characteristics－Part 6：Dispersion using a triple-roll mill

KS M ISO 8781-1-2007

颜料和体质颜料分散性的评定方法第1部分：着色颜料着色力变化的评定

Pigments and extenders－Methods of assessment of dispersion   characteristics－Part 1：Assessment   from the change in tinting strength of coloured pigments

KS M ISO 8781-2-2002

颜料和体质颜料分散性评定方法第2部分：磨碎细度变化评定

Pigments and extenders－Methods of assessment of dispersion   characteristics－Part 2：Assessment   from the change in fineness of grind

KS M ISO 8781-3-2002

颜料和体质颜料分散性评定方法第3部分：光泽变化评定

Pigments and extenders－Methods of assessment of dispersion   characteristics－Part 3：Assessment   from the change in gloss

KS M ISO 8784-1-2016

plup、纸和纸板－微生物检验－第1部分：基于分解的细菌、酵母菌和霉菌总数

Plup, paper and board－Microbiological examination－Part 1：Total count of bacteria, yeast and   mould based on disintegration

KS M ISO 8787-2016

纸和纸板毛细上升的测定克莱姆法

Paper and board－Determination of capillary rise－Klemm method

KS M ISO 8789-2014

机动车用气缸体用橡胶软管和软管组合件规范

Rubber hoses and hose assemblies for   liquefied petroleum gas in motor vehicles — Specification

KS M ISO 8791-1-2008

纸和纸板粗糙度和平滑度的测定（漏风法）第1部分：通用方法

Paper and board－Determination of roughness/smoothness   (air leak methods)－Part 1：General   method

KS M ISO 8791-2-2016

纸和纸板粗糙度和平滑度的测定（漏风法）第2部分：本特森法

Paper and board－Determination of roughness/smoothness   (air leak methods)－Part 2：Bendtsen   method

KS M ISO 8791-3-2016

纸和纸板粗糙度和平滑度的测定（漏气法）第3部分：谢菲尔德法

Paper and board－Determination of roughness/smoothness   (air leak methods)－Part 3：Sheffield   method

KS M ISO 8791-4-2008

纸和纸板粗糙度和平滑度的测定（漏风法）第4部分：印刷表面法

Paper and board－Determination of roughness/smoothness   (air leak methods)－Part 4：Print-surf   method

KS M ISO 8795-2008

人类生活用水输送用塑料管道系统迁移评定塑料管道及配件及其接头迁移值的测定

Plastics piping systems for the transport of   water intended for human consumption－Migration assessment－Determination of   migration values of plastics pipes and fittings and their joints

KS M ISO 8799-2014

表面活性剂.乙氧基化醇和烷基酚硫酸盐.未硫酸化物含量的测定

Surface active agents — Sulfated ethoxylated alcohols and   alkylphenols — Determination of content of unsulfated   matter

KS M ISO 8819-2003

液化石油气.硫化氢的测定.乙酸铅法

Liquefied petroleum gases－Detection of hydrogen sulfide－Lead acetate method

KS M ISO 893-2007

表面活性剂.工业烷烃磺酸盐.分析方法

Surface active agents－Technical alkane sulfonates－Methods of analysis

KS M ISO 894-2007

表面活性剂.工业伯烷基硫酸钠.分析方法

Surface active agents－Technical sodium primary   alkylsulphates－Methods of analysis

KS M ISO 895-2007

表面活性剂.工业仲烷基硫酸钠.分析方法

Surface active agents－Technical sodium secondary   alkylsulphates－Methods of analysis

KS M ISO 896-2007

表面活性剂.科学分类法.

Surface active agents－Scientific classification

KS M ISO 8973-2003

液化石油气.密度和蒸气压的计算

Liquefied petroleum gases－Calculation method for density and   vapour pressure

KS M ISO 8974-2010

塑料.酚醛树脂.用气体色谱法测定残余酚的含量

Plastics－Phenolic resins－Determination of residual   phenol content by gas chromatography

KS M ISO 8975-2010

塑料.酚醛树脂.pH值的测定

Plastics－Phenolic resins－Determination of pH

KS M ISO 8986-1-2013

塑料.聚丁烯模塑和挤塑材料.第1部分:命名体系和基本规范

PLASTIC — POLYBUTYLENE(PB) MOULDING AND EXTRUSION MATERIALS–PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS

KS M ISO 8986-2-2013

塑料.聚丁烯（PB）模塑和挤塑材料.第2部分：试样制备和性能测定

PLASTIC — POLYBUTYLENE(PB) MOULDING AND EXTRUSION MATERIALS–PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF   PROPERTIES

KS M ISO 8987-2016

塑料.酚醛树脂.在B-转变试验板上的活化性能的测定

Plastics－Phenolic resins－Determination of   reactivity on a B-transformation test plate

KS M ISO 8988-2010

塑料酚醛树脂六亚甲基四胺含量的测定凯氏法、高氯酸法和盐酸法

Plastics－Phenolic resins－Determination of   hexamethylenetetramine content－Kjeldahl method,   perchloric acid method and hydrochloric acid method

KS M ISO 8989-2010

塑料.液态酚醛树脂.水溶物的测定

Plastics－Liquid phenolic resins－Determination of   water miscibility

KS M ISO 899-1

塑料.蠕变性能的测定.第1部分:拉伸蠕变

Plastics－Determination of creep behavior－ Part 1：Tensile creep

KS M ISO 899-2

塑料蠕变性能的测定第2部分：三点加载弯曲蠕变

Plastics－Determination of creep behavior－Part 2：Flexural creep by three-point loading

KS M ISO 901-2003

主要用于铝生产的氧化铝.绝对密度的测定.比重瓶法

Aluminium oxide primarily used for the   production of aluminium－Determination   of absolute density－Pyknometer method

KS M ISO 902-2003

主要用于铝生产的氧化铝.休止角的测定

Aluminium oxide primarily used for the   production of aluminium－Measurement   of the angle of repose

KS M ISO 9026-2012

生橡胶或未硫化化合物生坯强度的测定

Raw rubber or unvulcanized compounds－ Determination of green strength

KS M ISO 9029-2003

原油.水分的测定.蒸馏法

Crude petroleum－Determination of water－Distillation method

KS M ISO 9030-2008

原油水和沉积物的测定离心法

Crude petroleum－Determination of water and sediment－Centrifuge method

KS M ISO 903-2003

主要用于铝生产的氧化铝.密度的测定

Aluminium oxide primarily used for the   production of aluminium－Determination   of untamped density

KS M ISO 9038-2013

液体持续可燃性的试验

Determination of sustained combustibility   of liquids

KS M ISO 904-2017

工业用盐酸.总酸度的测定.滴定法

Hydrochloric acid for industrial use — Determination of total acidity — Titrimetric method

KS M ISO 9054-2010

硬质泡沫塑料自结皮高密度材料试验方法

Cellular plastics, rigid－Test methods for   self-skinned,high-density materials

KS M ISO 9080-2015

塑料管道和导管系统.用外推法测定管形热塑性材料的长期流体静力学强度

Plastics piping and ducting systems — Determination of the longlongterm   hydrostatic strength of thermoplastics materials in pipe form by   extrapolation

KS M ISO 9088-2004

铝生产用碳素材料.预焙阳极和阴极块.用比重瓶法测定二甲苯密度

Carbonaceous materials for the production   of aluminium－Cathode blocks and pre－baked anodes－Determination of the density   in xylene by a pycnometric method

KS M ISO 910-2004

工业用硫酸和发烟硫酸.总酸度的测定以及发烟硫酸中游离三氧化硫含量的计算.滴定法

Sulphuric acid and oleum for industrial use－Determination of total acidity, and   calculation of free sulphur trioxide content of oleum－Titrimetric method

KS M ISO 91-1-2008

石油计量表.第2部分:以20℃为参比温度基础的表

Petroleum measurement tables-Part 1: Tables   based on a reference temperature of 15℃ and 60℉

KS M ISO 9112-2012

载重汽车和公共汽车轮胎.测量轮胎滚动周长的方法.承载新轮胎

Truck and bus tyres－Method of measuring tyre rolling and   bus tyres－Method of measuring tyre rolling

KS M ISO 9117-1-2017

色漆和清漆干燥试验第1部分：透干状态和透干时间的测定

Paints and varnishes－Drying tests－Part   1：Determination of through-dry state and through-dry   time

KS M ISO 9117-2-2012

色漆和清漆干燥试验第2部分：堆积性压力试验

Paints and varnishes－Drying tests－Part   2：Pressure test for stackability

KS M ISO 9117-3-2012

色漆和清漆干燥试验第3部分：微球体表面干燥试验

Paints and varnishes－Drying tests－Part   3：Surface-drying test using ballotini

KS M ISO 9117-4-2013

色漆和清漆.干燥试验.第4部分：使用机械记录器的试验

Paints and varnishes — Drying tests–Part 4: Test using a mechanical recorder

KS M ISO 9117-5-2013

色漆和清漆.干燥试验.第5部分：改进的Bandow-Wolff试验

Paints and varnishes — Drying tests–Part 5: Modified Bandow-Wolff test

KS M ISO 9117-6-2013

色漆和清漆.干燥试验.第6部分：无印痕试验

Paints and varnishes — Drying tests–Part 6: Print-free test

KS M ISO 91-2-2008

石油测量表第2部分：以20℃为基准的表

Petroleum meaurement tables-Part 2: Tables   based on a reference temperature of 20℃

KS M ISO 9120-2003

石油及相关产品.汽轮机油和其他油的空气释放性能的测定.冲击滤尘器法

Petroleum and related products－Determination of air release   properties of steam turbine and other oils－Impinger   method

KS M ISO 9142-2012

粘合剂.胶粘件试验用标准实验室老化条件的选择指南

Adhesives－Guide to the selection of standard laboratory ageing   conditions for testing bonded joints

KS M ISO 9149-2014

装饰用成卷复合软木条.规格

Cork wallcoverings in rolls — Specifications

KS M ISO 918-2017

工业用挥发性有机液体.蒸馏特性的测定

Volatile organic liquids for industrial use－Determination of distillation   characteristics

KS M ISO 9184-1-2016

纸、纸板和纸浆纤维成分分析第1部分：一般方法

Paper, board and pulps－Fibre furnish analysis－Part 1：General method

KS M ISO 9184-2-2017

纸、纸板和纸浆纤维成分分析第2部分：染色指南

Paper, board and pulps－Fibre furnish analysis－Part 2：Staining guide

KS M ISO 9184-3-2017

纸、纸板和纸浆纤维成分分析第3部分：赫茨伯格染色试验

Paper, board and pulps－Fibre furnish analysis－Part 3：Herzberg staining test

KS M ISO 9184-4-2017

纸、纸板和纸浆纤维成分分析第4部分：格拉夫“C”染色试验

Paper, board and pulps－Fibre furnish analysis－Part 4：Graff “C” staining test

KS M ISO 9184-5-2017

纸、纸板和纸浆纤维成分分析第5部分：洛夫顿-梅里特染色试验（纬纱的改性）

Paper, board and pulps－Fibre furnish analysis－Part 5：Lofton－Merritt   staining test(modification of Wisbar)

KS M ISO 9184-6-2017

纸、纸板和纸浆.纤维成分分析.第6部分：纤维粗度的测定

Paper, board and pulps — Fibre furnish analysis — Part 6: Determination of fibre coarseness

KS M ISO 9184-7-2017

纸、纸板和纸浆纤维成分分析第7部分：重量系数的测定

Paper, board and pulps－Fibre furnish analysis－Part 7：Determination of weight factor

KS M ISO 9197-2009

纸、纸板和纸浆.水可溶氯化物的测定

Paper, board and pulps－Determination of water-soluble   chlorides

KS M ISO 9198-2004

纸、纸板和纸浆.水溶性硫酸盐的测定

Paper, board and pulp－Determination of water-soluble   sulfates

KS M ISO 9298-2017

橡胶配合剂.氧化锌.试验方法

Rubber compounding ingredients－Zinc oxide－Test   methods

KS M ISO 9352-2013

塑料.用磨轮测定抗磨耗性能

Plastics — Determination of resistance to wear by abrasive   wheels

KS M ISO 9366-2004

集成（凝聚）软木.弹性地砖片尺寸和边缘的平直度和垂直度的测定

Agglomerated cork floor tiles－Determination of dimensions and   deviation from squareness and from straightness of edges

KS M ISO 9396-2010

塑料.酚醛树脂.使用自动装置对规定条件下酚醛树脂凝胶时间的测定

Plastics－Phenolic resins－Determination of the gel   time of resols under specific conditions using automatic apparatus

KS M ISO 9406-2004

铝生产用碳素材料.焦碳.用重量分析法测定挥发物的含量

Carbonaceous materials for the production   of aluminium－Green coke－Determination of volatile matter content by gravimetric analysis

KS M ISO 9407-2004

鞋号.世界鞋号的尺寸和标记体系

Shoes sizes－Mondopoint system of sizing and marking

KS M ISO 9413-2015

轮胎气门嘴.尺寸和规格

Tyre valves－Dimensions, designation, valve pressure ratings by use   and torque for clamp-in valves

KS M ISO 9416-2016

纸.光散射和吸收系数的测定（用库贝尔卡-芒克理论）

Paper－Determination of light scattering and absorption coefficients   (using Kubelka-Munk theory)

KS M ISO 9475-2010

飞机内胎和无内胎轮胎气门嘴芯和帽试验方法

Aircraft inner tube and tubeless tyre   valves－Cores and caps－Test methods

KS M ISO 9514-2011

色漆和清漆.液态体系适用期测定.样品的制备和处理以及试验指南

Paints and varnishes－Determination of the pot life of   multicomponent coating systems－Preparation and   conditioning of samples and guidelines for testing

KS M ISO 9631-2008

110℃热水管道用橡胶密封圈材料规范

Rubber seals－Joint rings for pipelines for hot-water supply up to   110 ℃－Specification for the material

KS M ISO 9653-2007

粘合剂.粘合件剪切冲击强度测定方法

Adhesives－Test method for shear impact strength of adhesive   bonds

KS M ISO 9664-2010

粘合剂.拉伸剪切胶粘件疲劳性能的试验方法

Adhesives－Test methods for fatigue properties of structural   adhesives in tensile shear

KS M ISO 9665-2010

粘合剂.动物胶.取样和试验方法

Adhesives－Animal glues－Methods of   sampling and testing

KS M ISO 9691-2008

橡胶管接头环工艺建议缺陷的描述和分类

Rubber－Recommendations for the workmanship of pipe joint rings－Description and classification of imperfections

KS M ISO 9702-2002

塑料.胺类环氧固化剂伯仲叔胺基含氮量的测定

Plastics－Amine epoxide hardners－Determination of   primary, secondary and tertiary amine group nitrogen content

KS M ISO 9706-2014

信息和文献.文件用纸.耐用性要求

Information and documentation — Paper for documents —Requirements for permanence

KS M ISO 9727-1-2009

圆柱形软木塞物理试验第1部分：尺寸的测定

Cylindrical cork stoppers－Physical tests－Part 1：Determination of dimensions

KS M ISO 9727-2-2009

圆柱形软木塞物理试验第2部分：胶凝软木塞质量和表观密度的测定

Cylindrical cork stoppers－Physical tests－Part 2：Determination of mass and apparent   density for agglomerated cork stoppers

KS M ISO 9727-3-2009

圆柱形软木塞物理试验第3部分：湿度的测定

Cylindrical cork stoppers－Physical tests－Part 3：Determination of humidity content

KS M ISO 9727-4-2009

圆柱形软木塞物理试验第4部分：压缩后尺寸恢复率的测定

Cylindrical cork stoppers－Physical tests－Part 4：Determination of dimensional   recovery after compression

KS M ISO 9727-5-2009

圆柱形软木塞物理试验第5部分：拔出力的测定

Cylindrical cork stoppers－Physical tests－Part 5：Determination of extraction force

KS M ISO 9727-6-2009

圆柱形软木塞物理试验第6部分：液体密封性的测定

Cylindrical cork stoppers－Physical tests－Part 6：Determination of liquid tightness

KS M ISO 9727-7-2009

圆柱形软木塞物理试验第7部分：粉尘含量的测定

Cylindrical cork stoppers－Physical tests－Part 7：Determination of dust content

KS M ISO 974-2002

塑料.冲击脆化温度的测定

Plastics－Determination of the brittleness temperature by impact

KS M ISO 976-2017

橡胶和塑料.聚合物分散体和橡胶胶乳.pH值的测定

Rubber and plastics－Polymer dispersions and rubber   latices－Determination of pH

KS M ISO 9772-2013

泡沫塑料在小火焰下小试样水平燃烧特性的测定

Cellular plastics ㅡ Determination of horizontal burning characteristics of   small specimens subjected to a small flame

KS M ISO 9773-2016

塑料立式软薄试样与小火源接触燃烧性能的测定

Plastics－Determination of burning behaviour of thin flexible vertical   specimens in contact with a small-flame ignition source

KS M ISO 9774-2012

建筑用隔热材料性能选择指南

Thermal insulation for building   applications－Guidelines for   selecting properties

KS M ISO 9782-2002

塑料.增强模塑料和预浸料.表观挥发物含量的测定

Plastics－Reinforced moulding compounds and prepregs－Determination of apparent volatile－matter   content

KS M ISO 979-2017

工业用氢氧化钠.试验方法

Sodium hydroxide for industrial use－Method of assay

KS M ISO 981-2017

工业用氢氧化钠.氯化物含量的测定.汞量法

Sodium hydroxide for industrial use — Determination of chloride content — Mercurimetric method

KS M ISO 9852-2016

未增塑聚氯乙烯(PVC-U)管材.在规定温度下抗二氯甲烷(DCMT)试验方法

Unplasticized polyvinyl chloride(PVC－U) pipes－   Dichloromethane resistance at specified temperature(DCMT)－Test method

KS M ISO 9853-2005

压力管道系统用硬聚氯乙烯(PVC-U)管件.扁平试验

Injection-moulded unplasticized poly(vinyl   chloride)(PVC－U) fittings for   pressure pipe systems－Crushing test

KS M ISO 9895-2009

纸和纸板抗压强度短跨距试验

Paper and board－Compressive strength－Short-span test

KS M ISO 9924-1-2017

橡胶和橡胶制品.用热重分析法测定硫化和未硫化化合物的成分.第1部分：丁二烯、乙烯-丙烯共聚物和三元共聚物、异丁烯-异戊二烯、异戊二烯和苯乙烯-丁二烯橡胶

Rubber and rubber products — Determination of the composition of   vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer,   isobutene-isoprene, isoprene and styrene-butadiene rubbers

KS M ISO 9924-2-2017

橡胶及橡胶制品硫化和未硫化化合物组成的测定热重法第2部分：丙烯腈-丁二烯和卤代丁基橡胶

Rubber and rubber products－Determination of the composition of   vulcanizates and uncured compounds by thermogravimetry－Part 2：Acrylonitrile－butadiene and halobutyl rubbers

KS M ISO 9924-3-2012

橡胶和橡胶制品热重分析法测定硫化和未硫化化合物的组成第3部分：硫化橡胶、卤化橡胶和聚硅氧烷橡胶

Rubber and rubber products－Determination of the composition of   vulcanizates and uncured compounds by thermogravimetry－ Part 3：Hyrocarbon rubbers, halogenated   rubbers and polysiloxane rubbers after extarction

KS M ISO 9932-2004

纸和纸板.薄页材料水蒸气透过率的测定.动态气流和静态气体扩散法

Paper and board－Determination of water vapour   transmission rate of sheet materials－Dynamic sweep   and static gas methods

KS M ISO 9950-2003

工业淬火油.冷却性的测定.镍合金探测试验法

Industrial quenching oils－Determination of cooling   characteristics－Nickel-alloy probe test methods

KS M ISO 9967-2016

热塑管.蠕变率测定

Thermoplastics pipes－Determination of creep ratio

KS M ISO 9969-2016

热塑性塑料管.环形硬度的测定

Thermoplastics pipes－Determination of ring stiffness

KS M ISO 9986-2004

鞋底用复合软木

Composition cork for shoe outsoles

KS M ISO 9988-1-2012

塑料.聚甲醛模塑和挤塑材料.第1部分:命名体系和基本规范

Plastics－Polyoxymethylene (POM) moulding and extrusion materials－Part 1：Designation system and basis for   specifications

KS M ISO 9988-2-2012

塑料聚甲醛（POM）模塑和挤塑材料第2部分：试样制备和性能测定

Plastics－Polyoxymethylene(POM) moulding and extrusion materials－Part 2：Preparation of test specimens and   determination of properties

KS M ISO TR 11340-2003

橡胶和橡胶制品.液压软管装置.液压系统的外部泄漏分类

Rubber and rubber products－Hydraulic hoes assemblies－External leakage classification for hydraulic systems

KS M ISO TR 15235-2012

涂装油漆和有关产品前钢材预处理水溶性盐污染水平影响的收集信息

Preparation of steel substrates before   application of paints and related products－Collected information on the effect of levels of water-soluble   salt contamination

KS M ISO TR 18690-2016

安全、防护和职业用鞋的选择、使用和维护指南

Guidance for the selection, use and   maintenance of safety,protective and occupational footwear

KS M ISO TR 20573-2008

鞋类－鞋类的性能要求－鞋跟和鞋帮

Footwear－Performance requirements for footwear－Heels   and top pieces

KS M ISO TR 20879-2008

鞋类鞋帮零部件性能要求

Footwear－Performance requirements for components for footwear－Uppers

KS M ISO TR 20880-2008

鞋类－鞋类零部件的性能要求－外底

Footwear－Performance requirements for components for footwear－Outsoles

KS M ISO TR 20881-2008

鞋靴.鞋靴部件的性能要求.内底

Footwear－Performance requirements for components for footwear－Insoles

KS M ISO TR 20882-2008

鞋靴零部件性能要求鞋衬和内垫

Footwear－Performance requirements for components for footwear－Lining and insocks

KS M ISO TR 24498-2008

纸、纸板和纸浆试验方法的不确定度评定

Paper, board and pulps－Estimation of uncertainty for test   methods

KS M ISO TR 4191-2005

给水用未增塑聚氯乙烯（PVC－U）管安装的推荐实施规程

Recommended practice for installation of   unplasticized polyvinyl chloride(PVC－U) pipes for water supply

KS M ISO TR 7074-2003

地下排污、废水工程用塑料管材和管件的性能要求

Performance requirements for plastics pipes   and fittings for use in underground drainage and sewage

KS M ISO TR 7620-2009

橡胶材料.耐化学性

Rubber materials－Chemical resistance

KS M ISO TR 7621-2003

橡胶或塑料包覆的辊筒.咨询和订货.买方提供的技术信息推荐

Rubber or plastics covered rollers－Enquiries and orders－Recommendations for technical information to be supplied by   purchaser

KS M ISO TR 8517-2003

橡胶或塑料涂覆胶辊.术语

Rubber－or plastics－covered rollers－Glossary