电子电气类标准(三)
2019-07-23 20:42标准号 | 中文名称 | 英文名称 |
KS C 8315-1990 | 接线盒 | Rosettes |
KS C 8318-1990 | 路灯开关 | Small Switches for Street Lamp |
KS C 8319-2012 | 平槽滤板 | Flush plates |
KS C 8321-2011 | 塑壳断路器 | Molded-Case Circuit-Breaker for industrial uses(MCCB) |
KS C 8324-2016 | 街路照明灯具用分线盒 | Cabinet type switchgear for street lights |
KS C 8326-2016 | 住宅用分线板 | Low voltage panelboards for household use |
KS C 8328-2002 | 漏电继电器 | Residual current sensing and relaying equipment |
KS C 8330-2014 | 25.8kv气绝缘负荷开关 | Gas insulated load break switch for 25.8 kV overhead line |
KS C 8331-1987 | 特高压交流断路器 | Alternative Circuit-Breaker for Extra-High Voltage, High Voltage |
KS C 8332-2018 | 产业用配线短路器 | Miniature circuit-breaker for overcurrent protection for household uses(MCB) |
KS C 8401-2016 | 刚性钢导管 | Rigid steel conduits |
KS C 8422-2005 | 软性钢导管 | Flexible metal conduits |
KS C 8425-2014 | 地板下线导管(钢质) | Underfloor ducts(steel) |
KS C 8431-2014 | 硬质未增塑聚氯乙烯(UPVC)导管 | Rigid unplasticized polyvinyl chloride(UPVC) conduits |
KS C 8433-2005 | 耦合(硬质塑料导管用) | Couplings(for rigid P.V.C conduit tubes) |
KS C 8434-2005 | 连接器(硬质塑料导管用) | Connectors(for rigid P.V.C conduit tubes) |
KS C 8436-2012 | 合成树脂箱和盖 | Boxes and covers of plastic conduits |
KS C 8438-A-2014 | 金属质导管配件通则 | General rules for fittings of metal conduits and underfloor ducts |
KS C 8449-2002 | 触轮母线槽 | Trolley busways |
KS C 8452-2002 | 室内布线用接分(接)线盒(聚氯乙烯绝缘和护套电缆) | Junction box for indoor wiring(for polyvinyl-chloride insulated and sheathed cables:VVF) |
KS C 8454-2006 | 软性合成树脂分(接)线盒 | Pliable plastics conduits |
KS C 8455-2016 | 波纹硬质聚乙烯分(接)线盒 | Corrugated hard polyethylene pipe |
KS C 8456-2005 | 软性合成树脂导管配件 | Fittings for pliable plastics conduits |
KS C 8457-2005 | 地板下线导管配件 | Fittings for underfloor ducts |
KS C 8458-2012 | 金属质箱和箱盖(导管用) | Box and box cover for rigid metal conduits |
KS C 8459-2005 | 软性金属质导管配件 | Fittings for flexible metal conduits |
KS C 8460-2005 | 金属质导管配件 | Fittings for rigid metal conduits |
KS C 8461-2005 | 露天排管用配件(导管用) | Surface accessary for rigid metal conduits |
KS C 8463-1997 | 电梯按键开关盒 | Boxes for elevator call button switch |
KS C 8464-2016 | 电缆托盘 | Cable tray |
KS C 8465-2008 | 电缆管道 | Raceway |
KS C 8501-2014 | 锰干电池 | Manganese dry cells and batteries |
KS C 8503-2005 | 二氧化锰锂原电池 | Manganese dioxide lithium primary cells and batteries |
KS C 8504-2015 | 汽车用铅酸蓄电池 | Lead-acid batteries for automobiles |
KS C 8505-2008 | 固定型铅酸蓄电池 | Stationary lead-acid batteries |
KS C 8508-2005 | 火车用蓄电池 | Batteries for train |
KS C 8509-2004 | 内燃机车用蓄电池 | Batteries for diesel locomotives |
KS C 8510-2003 | 摩托车用铅酸蓄电池 | Lead-acid batteries for motorcycles |
KS C 8511-2003 | 电动车用蓄电池 | Lead-acid batteries for motor train |
KS C 8513-2014 | 碱性一次电池和电池组 | Alkaline primary cells and batteries |
KS C 8515-2003 | 圆柱密封镉镍可充单体电池 | Sealed nickel-cadmium, cylindrical rechargeable single cells |
KS C 8516-1987 | 氯化碳锂一次电池和电池组 | Carbon-monofluoride Lithium Primary Cells and Butteries |
KS C 8517-2002 | 通风式镉镍棱柱形蓄电池 | Vented nickel-cadmium prismatic secondary single cells |
KS C 8518-2018 | 密封固定型铅酸蓄电池 | Stationary sealed lead - acid batteries(valve regulated types) |
KS C 8519-1999 | 小型密封铅酸蓄电池 | Smallsized sealed leadacid batteries(valve regulated types) |
KS C 8520-2003 | 一次电池通则 | Primary batteries:General |
KS C 8526-2005 | 晶体基太阳电池模块输出功率的测量方法 | Measuring method of output power crystalline solar cell modules |
KS C 8528-2005 | 晶体基太阳电池输出功率的测量方法 | Measuring method of output power for crystalline solar cells |
KS C 8529-1995 | 晶体基太阳电池模块的输出电压、输出电流的温度系数测定方法 | Temperature coefficient measuring methods for crystalline solar cells and modules |
KS C 8532-1995 | 太阳光伏能源系统用铅酸蓄电池的残余电容测定方法 | Measuring procedure of residual capacity for lead acid battery in photovoltaic system |
KS C 8533-2002 | 太阳光伏能源系统用功率调节效率测定方法 | Measuring procedure of power conditioner efficiencyfor photovoltaic systems |
KS C 8534-2002 | 太阳电池组输出的i-v实测特性测试方法 | On-site measurements of photovoltaic array I-V characteristics |
KS C 8535-2005 | 太阳光伏能源系统运行特性测定方法 | Measuring procedure of photovoltaic system performance |
KS C 8536-2005 | 独立型太阳光伏能源系统通则 | General rules for stand-alone photovoltaic power generating system |
KS C 8538-2000 | 微晶太阳电池输出功率测定方法 | Measuring method of output power for amorphous solar cells |
KS C 8539-2005 | 太阳光伏能源系统的长时间放电铅酸蓄电池试验法 | Testing procedure of long discharge rate lead-acid batteries for photovoltaic systems |
KS C 8540-2005 | 小型太阳光伏能源系统的功率调节器试验法 | Testing procedure of power conditioner forsmall photovoltaic power generating systems |
KS C 8541-2003 | 锂二次电池通则 | Lithium secondary cells and batteries:General |
KS C 8542-2003 | 锂二次电池术语 | Glossary of terms for secondary cells and batteries |
KS C 8543-2015 | 排气型镍.金属氢化物(镍/MH)电池 | Vented nickel-metal hydride secondary cells |
KS C 8544-2016 | 密封镍金属氢化物二次电池 | Sealed nickel-metal hydride secondary cells |
KS C 8545-2006 | 携带设备用锂二次单电池的安全标准 | Safety requirements for lithium secondary cells for portable applications |
KS C 8546-2008 | 便携式设备用锂二次电池的安全性测试 | Safety tests for lithium secondary cells and batteries for portable applications |
KS C 8547-2017 | 储能系统用氧化还原液流电池.性能和安全试验 | Redox flow battery for use in energy storage system — Performance and safety tests |
KS C 8548-2016 | 电池储能系统术语表二次锂电池系统 | Glossary of BESS(Battery Energy Storage System) ― Secondary Lithium Battery Systems |
KS C 8560-2016 | 光伏微逆变器(并网型、单机型) | Photovoltaic microinverter(grid-tied type, stand-alone type) |
KS C 8561-2016 | 晶体硅光伏组件(性能) | Crystalline silicone photovoltaic(PV) module(performance) |
KS C 8562-2015 | 薄膜光伏发电模块(性能) | Thin film photovoltaic(PV) module(performance) |
KS C 8563-2015 | 太阳能发电模块(性能) | Photovoltaic(PV) module(safety qualification) |
KS C 8564-2016 | 小型光伏逆变器(并网型、单机型) | Small scale photovoltaic inverter(grid-tied type, stand-alone type) |
KS C 8565-2016 | 大中型光伏逆变器(并网型、单机型) | Medium and large size photovoltaic inverter(grid-tied type, stand-alone type) |
KS C 8566-2015 | 光电池 | Solar Cell |
KS C 8567-2017 | 太阳能接线盒 | Connection box for solar power |
KS C 8568-2015 | 太阳能聚集器 | Solar collector |
KS C 8569-2015 | 聚合物电解质燃料电池系统 | Polymer electrolyte fuel cell(PEFC) system |
KS C 8570-2015 | 小型风力发电机组 | Small wind turbines |
KS C 8571-2015 | 小型风力发电用变频器 | Inverter for small wind turbines |
KS C 8572-2015 | 陆地用中大型风力发电设计要求 | Design requirements for onshore large and medium-sized wind turbines |
KS C 8573-2015 | 海上用中大型风力发电设计要求 | Design requirements for offshore large and medium-sized wind turbines |
KS C 8574-2015 | 充电控制系统 | Balance-of-system components for photovoltaic systems — Charging control system |
KS C 8575-2015 | 蓄电池 | Storage battery |
KS C 8576-2015 | 监护设备 | Monitoring equipment |
KS C 8577-2016 | 建筑集成光电(BIPV)模块性能评估要求 | Building integrated photovoltaics(BIPV) modules — The requirement of performance evaluation |
KS C 9001-2004 | 弧焊机通则 | General rules for Arc Welder |
KS C 9040-2-2017 | 不间断电源系统第2部分:电磁兼容性要求 | Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements |
KS C 9101-2014 | 真空吸尘器 | Electric vacuum cleaners |
KS C 9102-2002 | 便携式电刨 | Portable electric planers |
KS C 9103-2002 | 便携式圆电锯 | Portable electric circular saws |
KS C 9206-2013 | 电烤面包机 | Electric toasters and roasters for household |
KS C 9209-2013 | 卷发机 | Hair curling appliances and hand-hold hair dryers |
KS C 9220-2013 | 电热炕板 | Electric heated resin sheet and heated over-blankets and under-blankets |
KS C 9301-2013 | 电风扇 | Electric fans and ceiling fans |
KS C 9304-2002 | 排气扇 | Ventilating fans |
KS C 9306-2017 | 空气调节器 | Air conditioners |
KS C 9309-2013 | 电水壶 | Electric pots and water heaters |
KS C 9310-2013 | 电饭锅 | Electric rice-cookers and rice jars with electric thermal control |
KS C 9313-2013 | 微波炉 | Microwave ovens |
KS C 9314-2013 | 空气清净机 | Air cleaners |
KS C 9315-2013 | 饮料用电冷水机 | Drinking-water coolers |
KS C 9317-2013 | 除湿机 | Dehumidifiers |
KS C 9319-2013 | 旋转滚筒式衣类干燥机 | Tumbler type electric clothe dryers |
KS C 9321-2014 | 泡菜电储藏箱 | Electrical storage box for kimchi |
KS C 9322-2013 | 炕式电动床 | Electric beds of Ondol type |
KS C 9325-2011 | 空气净化器、过滤器 | Air filter element for room air cleaners |
KS C 9547-2017 | 通用照明设备电磁兼容抗扰度要求 | Equipment for general lighting purposes ― EMC immunity requirements |
KS C 9602-2007 | 交流弧焊机 | AC arc welding machines |
KS C 9605-1997 | 整流式直流弧焊机 | Rectifier type DC arc welding machines with drooping characteristics |
KS C 9607-1998 | 弧焊机电焊钳 | Welding electrode holders for arc welding |
KS C 9608-2013 | 洗衣机 | Electric washing machines |
KS C 9610-2-2017 | 电磁兼容(EMC)第2-2部分:环境公用低压供电系统低频传导骚扰和信号的兼容水平 | Electromagnetic compatibility (EMC) ― Part 2―2: Environment ― Compatibility levels for low ― frequency conducted disturbances and signalling in public low ― voltage power supply systems |
KS C 9610-2-2017 | 电磁兼容第2-4部分:环境工业设备低频传导骚扰的兼容水平 | Electromagnetic compatibility (EMC) ― Part 2―4: Environment ― Compatibility levels in industrial plants for low ― frequency conducted disturbances |
KS C 9610-3-2017 | 电磁兼容性(EMC)-第3-11部分:限值-公用低压供电系统中电压变化、电压波动和闪烁的限制-额定电流≤75A并有条件连接的设备 | Electromagnetic compatibility (EMC)- Part 3-11: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current ≤ 75 A and subject to conditional connection |
KS C 9610-3-2017 | 电磁兼容性(EMC).第3-12部分:限值.与每相输入电流大于16A且小于等于75A的公共低压系统连接的设备产生的谐波电流的限值 | Electromagnetic compatibility(EMC) — Part 3-12: Limits — Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and ≤ 75 A per phase |
KS C 9610-3-2017 | 电磁兼容(EMC)第3-2部分:限值谐波电流发射限值(设备输入电流每相≤16A) | Electromagnetic compatibility(EMC) ― Part 3―2: Limits ― Limits for harmonic current emissions(equipment input current ≤ 16 A per phase |
KS C 9610-3-2017 | 电磁兼容(EMC)第3-3部分:限值公共低压供电系统中电压变化、电压波动和闪变的限值额定电流每相小于等于16A且无条件连接的设备用电压供应系统 | Electromagnetic compatibility(EMC) ― Part 3―3: Limits ― Limitation of voltage changes, voltage fluctuations and flicker in public low ― voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection |
KS C 9610-4-2017 | 电磁兼容(EMC)第4-11部分:试验和测量技术电压暂降、短时中断和电压变化抗扰度试验 | Electromagnetic compatibility(EMC) ― Part 4-11: Testing and measurement techniques — Voltage dips, short interruptions and voltage variations immunity tests |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-2部分:试验和测量技术静电放电抗扰度试验 | Electromagnetic compatibility (EMC) — Part 4—2: Testing and meaeurement techniques — Electrostatic discharge immunity test |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-3部分:试验和测量技术辐射、射频、电磁场抗扰度试验 | Electromagnetic compatibility(EMC) — Part 4-3: Testing and measurement techniques — Radiated, radio-frequency, electromagnetic field immunity test |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-4部分:试验和测量技术电快速瞬变脉冲群抗扰度试验 | Electromagnetic compatibility(EMC) — Part 4-4: Testing and measurement techniques — Electrical fast transient/burst immunity test |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-5部分:试验和测量技术浪涌抗扰度试验 | Electromagnetic compatibility(EMC) — Part 4-5: Testing and measurement techniques — Surge immunity test |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-6部分:试验和测量技术射频场感应的传导骚扰抗扰度 | Electromagnetic compatibility(EMC) — Part 4-6: Testing and measurement techniques — Immunity to conducted disturbances, induced by radio-frequency fields |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-8部分:试验和测量技术工频磁场抗扰度试验 | Electromagnetic compatibility(EMC) — Part 4-8: Testing and measurement techniques — Power frequency magnetic field immunity test |
KS C 9610-4-2017 | 电磁兼容性(EMC)第4-9部分:试验和测量技术脉冲磁场抗扰度试验 | Electromagnetic compatibility(EMC) — Part 4-9: Testing and measurement techniques — Pulse magnetic field immunity test |
KS C 9610-6-2017 | 电磁兼容性(EMC)第6-1部分:通用标准住宅、商业和轻工业环境的抗扰度 | Electromagnetic compatibility(EMC) — Part 6-1: Generic standards — Immunity for residential, commercial and light-industrial environments |
KS C 9610-6-2017 | 电磁兼容性(EMC)第6-2部分:通用标准工业环境抗扰度 | Electromagnetic compatibility(EMC) — Part 6-2: Generic standards — Immunity for industrial environments |
KS C 9610-6-2017 | 电磁兼容性(EMC)第6-3部分:通用标准住宅、商业和轻工业环境的发射标准 | Electromagnetic compatibility(EMC) — Part 6-3: Generic standards — Emission standard for residential, commercial and lightindustrial environments |
KS C 9610-6-2017 | 电磁兼容性(EMC)第6-4部分:通用标准工业环境排放标准 | Electromagnetic compatibility(EMC) — Part 6-4: Generic standards — Emission standard for industrial environments |
KS C 9615-2002 | 便携式电钻 | Hand-held electric drills |
KS C 9619-2014 | 家用小型单相变压器 | Small single phase transformer for household purpose |
KS C 9627-2002 | 电动盘式砂轮机 | Hand-held electric grinders |
KS C 9630-2003 | 三相自动干燥式小型变压器 | Three-phase separating dry-type small transfomer |
KS C 9706-2014 | 超声眼科生物测量仪 | Ultrasonic ophthalmic biometers |
KS C 9707-1996 | 诊断用磁共振设备.图形及标志 | Graphical symbols and sign for magnetic resonance equipment for medical diagnosis |
KS C 9708-1997 | 诊断用磁共振成像设备 | Phantoms for magnetic resonance equipment for medical diagnosis |
KS C 9800-3-2017 | 可调速电力驱动系统.第3部分:电磁兼容性要求和特殊试验方法 | Adjustable speed electrical power drive systems — Part 3: EMC requirements and specific test methods |
KS C 9801-1992 | 干电池型蜂音器 | Dry battery type buzzers |
KS C 9802-1997 | 交流电蜂音器 | AC buzzers |
KS C 9805-2013 | 家用蓄热式电饭锅 | Electric storage water boilers for household purposes and storage tank water heaters |
KS C 9806-2014 | 数码门锁 | Digital door locks |
KS C 9811-2017 | 工业、科学和医疗设备.射频干扰特性.限值和测量方法 | Industrial, scientific and medical equipment — Radio-frequency disturbance characteristics — Limits and methods of measurement |
KS C 9814-1-2017 | 电磁兼容性(EMC)——家用电器、电动工具和类似设备的要求——第1部分:发射 | Electromagnetic compatibility (EMC) ― Requirements for household appliances, electric tools and similar apparatus ― Part 1: Emission |
KS C 9814-2-2017 | 电磁兼容家用电器、电动工具及类似器具的要求第2部分:抗扰度产品族标准 | Electromagnetic compatibility ― Requirements for household appliances, electric tools and similar apparatus ― Part 2: Immunity ― Product family standard |
KS C 9815-2017 | 电气照明和类似设备无线电骚扰特性的限值和测量方法 | Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment |
KS C 9816-1-2017 | 无线电骚扰和抗扰度测量仪器和测量方法规范第1部分:无线电骚扰和抗扰度测量仪器测量仪器 | Specification for radio disturbance and immunity measuring apparatus and methods ― Part 1―1: Radio disturbance and immunity measuring apparatus ― Measuring apparatus |
KS C 9816-1-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第1-2部分:无线电骚扰和抗扰度测量设备传导骚扰测量用耦合设备 | Specification for radio disturbance and immunity measuring apparatus and methods ― Part 1―2: Radio disturbance and immunity measuring apparatus ― Coupling devices for conducted disturbance measurements |
KS C 9816-1-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第1-3部分:无线电骚扰和抗扰度测量设备辅助设备骚扰功率 | Specification for radio disturbance and immunity measuring apparatus and methods ― Part 1―3: Radio disturbance and immunity measuring apparatus ― Ancillary equipment ― Disturbance power |
KS C 9816-1-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第1-4部分:无线电骚扰和抗扰度测量设备辐射骚扰测量用天线和测试场地 | Specification for radio disturbance and immunity measuring apparatus and methods ― Part 1―4: Radio disturbance and immunity measuring apparatus ― Antennas and test sites for radiated disturbance measurements |
KS C 9816-1-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第1-5部分:无线电骚扰和抗扰度测量设备30MHz至1000MHz的校准和参考的规范和验证程序 | Specification for radio disturbance and immunity measuring apparatus and methods – Part 1–5: Radio disturbance and immunity measuring apparatus – Specifications and validation procedures for CALTS and REFTS from 30 MHz to 1 000 MHz |
KS C 9816-2-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第2-1部分:骚扰和抗扰度测量方法传导骚扰测量 | Specification for radio disturbance and immunity measuring apparatus and methods ― Part 2―1: Methods of measurement of disturbances and immunity ― Conducted disturbance measurements |
KS C 9816-2-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第2-2部分:骚扰和抗扰度测量方法骚扰功率的测量 | Specification for radio disturbance and immunity measuring apparatus and methods — Part 2-2: Methods of measurement of disturbances and immunity — Measurement of disturbance power |
KS C 9816-2-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第2-3部分:骚扰和抗扰度测量方法辐射骚扰测量 | Specification for radio disturbance and immunity measuring apparatus and methods — Part 2-3: Methods of measurement of disturbances and immunity — Radiated disturbance measurements |
KS C 9816-2-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第2-4部分:骚扰和抗扰度测量方法抗扰度测量 | Specification for radio disturbance and immunity measuring apparatus and methods — Part 2-4: Methods of measurement of disturbances and immunity — Immunity measurements |
KS C 9816-2-2017 | 无线电骚扰和抗扰度测量设备和测量方法规范第2-5部分:物理大型设备产生的骚扰发射的现场测量 | Specification for radio disturbance and immunity measuring apparatus and methods — Part 2-5: In situ measurements of disturbing emissions produced by physically large equipment |
KS C 9974-10-2017 | 弧焊设备第10部分:电磁兼容性要求 | Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements |
KS C 9990-2017 | 关于审核车辆电磁兼容性的统一规定 | Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility |
KS C CISPR 12-2011 | 运载工具、摩托艇和火花点火发动机驱动装置.无线电干扰特性.极限值和测量方法 | Vehicles, boats and internal combustion engines-Radio disturbance characteristics-Limits and methods of measurement for the protection of off-board receivers |
KS C CISPR 13-2011 | 无线电广播接收机及其有关装置无线电干扰特性的测量方法与极限 | Sound and television broadcast receivers and associated equipment-Radio disturbance characteristics-Limits and methods of measurement |
KS C CISPR 17-2014 | 手动电磁骚扰滤波器和抑制元件抑制特性的测量方法 | Methods of measurement of the suppression characteristics of passive radio interference filters and suppression components |
KS C CISPR 20-2014 | 声音与电视广播接收机及相关设备-免疫力特性-限制值与量测方法 | Sound and television broadcast receivers and associated equipment — Immunity characteristics — Limits and methods of measurement |
KS C CISPR 22-2011 | 信息技术设备的无线电骚扰限值和测量方法 | Information technology equipment-Radio disturbance characteristics-Limits and methods of measurement |
KS C CISPR 24-2014 | 信息技术设备.抗扰特性.技术设备.抗扰特性- | Information technology equipment — Immunity characteristics —technology equipment — Immunity characteristics — |
KS C CISPR 25-2011 | 用于保护车载接收机的电磁骚扰特性的限值和测量方法 | Vehicles, boats and internal combustion engines-Radio disturbance characteristics-Limits and methods of measurement for the protection of on-board receivers |
KS C CISPR 28-2002 | 工业、科学和医疗设备(ISM)-国际电信联盟(ITU)指定频段内的电磁辐射限值 | Industrial, scientific and medical equipment(ISM)-Guidelines for emission levels within the bands designated by the ITU |
KS C CISPR 30-2003 | 单头、双头荧光灯用电磁式镇流器电磁骚扰特性的测量方法 | Test method on electromagnetic emissions from electronic ballast for single-and double-capped fluorescent lamps |
KS C CISPR 31-2007 | 电波服务特性相关的数据库 | Database on the characteristics of radio services |
KS C CISPR TR 16-4-2012 | 无线电干扰和抗扰度测量设备和测定方法规定.第4-1部分:不确定度、统计学和限值建模标准化的EMC试验的不确定性 | Specification for radio disturbance and immunity measuring apparatus and methods-Part 4-1:Uncertainties, statistics and limit modelling-Uncertainties in standardized EMC tests |
KS C CISPR TR 18-1-2012 | 架空电力线路和高压设备的无线电干扰特性.第1部分:现象相关技术 | Radio interference characteristics of overhead power lines and high-voltage equipment-Part 1:Description of phenomena |
KS C CISPR TR 18-2-2012 | 架空电力线路和高压设备的无线电干扰特性.第2部分:确定阈值的测量方法和程序 | Radio interference characteristics of overhead power lines and high-voltage equipment-Part 2:Methods of measurement and procedure for determining limits |
KS C CISPR TR 18-3-2012 | 架空电力线路和高压设备的无线电干扰特性.第3部分:减少产生无线噪音发生的管理指南 | Radio interference characteristics of overhead power lines and high-voltage equipment-Part 3:Code of practice for minimizing the generation of radio noise |
KS C IEC 60027-1-2009 | 电工技术用字母符号.第1部分:总则 | Letter symbols to be used in electrical technology-Part 1:General |
KS C IEC 60027-2-2009 | 电气技术用字母符号.第2部分:电信和电子学 | Letter symbols to be used in electrical technology-Part 2:Telecommunications and electronics |
KS C IEC 60027-3-2009 | 电气技术用字母符号.第3部分:对数和有关量及其单位 | Letter symbols to be used in electrical technology-Part 3:Logarithmic quantities and units |
KS C IEC 60027-4-2009 | 电气技术用字母符号.第4部分:旋转电机 | Letter symbols to be used in electrical technology-Part 4:Symbols for quantities to be used for rotating electrical machines |
KS C IEC 60028-2003 | 铜电阻国际标准 | International standard of resistance for copper |
KS C IEC 60034-1-2008 | 旋转电机第1部分:额定值和性能 | Rotating electrical machines-Part 1:Rating and performance |
KS C IEC 60034-11-2008 | 旋转电机第11部分:热保护 | Rotating electrical machines-Part 11:Thermal protection |
KS C IEC 60034-12-2008 | 旋转电机第12部分:电压660V及以下单相笼型感应电动机起动性能 | Rotating electrical machines-Part 12:Starting performance of single-speed three-phase cage induction motors for voltages up to and including 660 V |
KS C IEC 60034-14-2008 | 旋转电机第14部分:轴高56mm及以上电机的机械振动测量、评定和振动烈度限值 | Rotating electrical machines-Part 14:Mechanical vibration of certain machines with shaft heights 56 mm and higher-Measurement, evaluation and limits of vibration severity |
KS C IEC 60034-15-2002 | 旋转电机第15部分:带成型绕线定子线圈的旋转交流电机的冲击电压耐受水平 | Rotating electrical machines Part 15:Impulse voltage withstand levels of rotating a.c. machines with form-wound stator coils |
KS C IEC 60034-16-2002 | 旋转电机第16部分:同步电机励磁系统第1章:定义 | Rotating electrical machines-Part 16:Excitation systems for synchronous machines-Chapter 1:Definitions |
KS C IEC 60034-16-2014 | 旋转电机第16部分:同步电机励磁系统第2章:电力系统研究模型 | Rotating electrical machines — Part 16: Excitation systems for synchronous machines — Chapter 2: Models for power system studies |
KS C IEC 60034-16-2014 | 旋转电机第16部分:同步电机励磁系统第3节:动态性能 | Rotating electrical machines — Part 16: Excitation systems for synchronous machines — Section 3: Dynamic performance |
KS C IEC 60034-17-2014 | 旋转电机.第17部分:由变频器供电的笼式感应电动机.应用指南 | Rotating electrical machines — Part 17: Cage induction motors when fed from converters — Application guide |
KS C IEC 60034-18-2002 | 旋转电机?第18部分:绝缘系统的功能评估?第1节:通用指南 | Rotating electrical machines - Part18 : Functional evalution of insulation systems - Section1:General Guidelines |
KS C IEC 60034-18-2002 | 旋转电机第18部分:绝缘结构功能性评定第21节:绕线绕组试验规程热评定和分级 | Rotating electrical machines-Part 18: Functional evaluation of insulation systems-Section 21: Test procedures for wire-wound windings-Thermal evaluation and classification |
KS C IEC 60034-18-2003 | 旋转电机第18-22部分:绝缘结构功能性评定绕线绕组试验规程变化分类和绝缘元件替换 | Rotating electrical machines-Part 18-22:Functional evaluation of insulation systems-Test procedures for wire - wound windings-Classification of changes and insulation component substitutions |
KS C IEC 60034-18-2003 | 旋转电机第18-31部分:绝缘结构功能性评定成型绕组试验规程50MVA和15kV及以下电机绝缘结构热评定和分级 | Rotating electrical machines-Part 18-31:Functional evaluation of insulation systems-Test procedures for form-wound windings-Thermal evaluation and classification of insulation systems used in machines up to and including 50 MVA and 15 kV |
KS C IEC 60034-18-2014 | 旋转电机第18-32部分:绝缘结构功能性评定成型绕组试验规程电气耐久性评定 | Rotating electrical machines — Part 18-32: Functional evaluation of insulation systems — Test procedures for form-wound windings — Evaluation by electrical endurance |
KS C IEC 60034-18-2014 | 旋转电机第18-33部分:绝缘结构功能性评定成型绕组试验规程同时承受热应力和电应力的多因素耐久性评定 | Rotating electrical machines — Part 18-33: Functional evaluation of insulation systems — Test procedures for form-wound windings — Multifactor evaluation by endurance under simultaneous thermal and electrical stresses |
KS C IEC 60034-19-2002 | 旋转电机第19部分:常规和整流供电直流电机特殊试验方法 | Rotating electrical machines-Part 19 : Specific test methods for d.c. machines on conventional and rectifier-fed supplies |
KS C IEC 60034-2-2008 | 旋转电机第2-1部分:试验损耗和效率测定的标准方法(不包括牵引车用电机) | Rotating electrical machines-Part 2-1:Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) |
KS C IEC 60034-22-2002 | 旋转电机第22部分:往复式内燃机驱动的发电机组用交流发电机 | Rotating electrical machines-Part 22 : AC generators for reciprocating internal combustion(RIC) engine driven generating sets |
KS C IEC 60034-26-2014 | 旋转电机第26部分:不平衡电压对三相笼型感应电动机性能的影响 | Rotating electrical machines — Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors |
KS C IEC 60034-28-2014 | 旋转电机第28部分:三相低压笼型感应电动机等效电路图数量的测定方法 | Rotating electrical machines — Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors |
KS C IEC 60034-29-2014 | 旋转电机.第29部分:等效负载和叠加技术.测定温升的间接试验 | Rotating electrical machines — Part 29: Equivalent loading and superposition techniques — Indirect testing to determine temperature rise |
KS C IEC 60034-3-2008 | 旋转电机第3部分:汽轮机或燃气轮机驱动的同步发电机的特殊要求 | Rotating electrical machines-Part 3:Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines |
KS C IEC 60034-4-2002 | 旋转电机第4部分:试验确定同步电机数量的方法 | Rotating electrical machines-Part 4:Methods for determining synchronous machine quantities from tests |
KS C IEC 60034-5-2008 | 旋转电机第5部分:旋转电机整体设计防护等级(IP代码)-分类 | Rotating electrical machines-Part 5:Degrees of protection provided by the integral design of rotating electrical machines(IP code)-Classification |
KS C IEC 60034-6-2002 | 旋转电机第6部分:冷却方法(IC代码) | Rotating electrical machines-Part 6:Methods of cooling(IC Code) |
KS C IEC 60034-7-2010 | 旋转电机第7部分:结构型式、安装方式和接线盒位置的分类(IM代码) | Rotating electrical machines-Part 7:Classification of types of construction, mounting arrangements and terminal box position(IM Code) |
KS C IEC 60034-8-2008 | 旋转电机第8部分:端子标记和旋转方向 | Rotating electrical machines-Part 8:Terminal markings and direction of rotation |
KS C IEC 60034-9-2002 | 旋转电机第9部分:噪声限值 | Rotating electrical machines-Part 9:Noise limits |
KS C IEC 60041-2014 | 测定水轮机、蓄能泵和水泵-水轮机水力性能的现场验收试验 | Field acceptance tests to determine the hydraulic performance of hydraulic turbines, storage pumps and pump-turbines |
KS C IEC 60044-1-2003 | 互感器第1部分:电流互感器 | Instrument transformers-Part 1:Current transformers |
KS C IEC 60044-2-2003 | 互感器第2部分:感应电压互感器 | Instrument transformers-Part 2:Inductive voltage transfomers |
KS C IEC 60044-3-2003 | 仪表用变压器第3部分:组合式变压器 | Instrument transformers-Part 3:Combined transformers |
KS C IEC 60044-5-2003 | 互感器第5部分:电容式电压互感器 | Instrument transformers-Part 5:Capacitor voltage transformers |
KS C IEC 60044-6-2003 | 互感器第6部分:保护用电流互感器暂态性能要求 | Instrument transformers-Part 6:Requirements for protective current transformers for transient performance |
KS C IEC 60044-7-2003 | 互感器第7部分:电子式电压互感器 | Instrument transformers-Part 7:Electronic voltage transformers |
KS C IEC 60044-8-2003 | 互感器第8部分:电子式电流互感器 | Instrument transformers-Part 8:Electronic current transformers |
KS C IEC 60050-101-2012 | 国际电工词汇第101部分:数学 | International Electrotechnical Vocabulary-Part 101:Mathematics |
KS C IEC 60050-112-2018 | 国际电工词汇第112部分:量和单位 | International electrotechnical vocabulary — Part 112: Quantities and units |
KS C IEC 60050-151-2018 | 国际电工词汇第151部分:电气和磁性器件 | International Electrotechnical Vocabulary — Part 151: Electrical and magnetic devices |
KS C IEC 60050-161-2018 | 国际电工词汇第161部分:电磁兼容性 | International electrotechnical vocabulary — Part 161:Electromagnetic compatibility |
KS C IEC 60050-191-2016 | 国际电工词汇第191章:可靠性和服务质量 | International Electrotechnical Vocabulary — Chapter 191: Dependability and quality of service |
KS C IEC 60050-195-2003 | 国际电工词汇第195部分:接地和电击防护 | International Electrotechnical Vocabulary-Part 195:Earthing and protection against electric shock |
KS C IEC 60050-221-2016 | 国际电工词汇第221章:磁性材料和元件 | International Electrotechnical Vocabulary - Chapter 221: Magnetic materials and components |
KS C IEC 60050-411-2001 | 国际电工词汇第411章:旋转电机 | International electrotechnical vocabulary-Chapter 411:Rotating machines |
KS C IEC 60050-415-2003 | 国际电工词汇第415部分:风力发电机组 | International Electrotechnical Vocabulary-Part 415:Wind turbine generator systems |
KS C IEC 60050-421-2001 | 国际电工词汇第421章:电力变压器和电抗器 | International electrotechnical vocabulary-Chapter 421:Power transformers and reactors |
KS C IEC 60050-441-2001 | 国际电工词汇第441章:开关设备、控制设备和保险丝 | International electrotechnical vocabulary-Chapter 441:Switchgear, controlgear and fuses |
KS C IEC 60050-445-2018 | 国际电工词汇第445部分:时间继电器 | International electrotechnical vocabulary — Part 445: Time relays |
KS C IEC 60050-482-2006 | 国际电工词汇第482部分:原电池和蓄电池 | International electrotechnical vocabulary-Part 482:Primary and secondary cells and batteries |
KS C IEC 60050-521-2002 | 半导体器件和集成电路 | Semiconductor devices and integrated circuits |
KS C IEC 60050-541-2003 | 国际电工词汇第541章:印制电路 | Intrenational electrotechnical vocabulary-Chapter 541:Printed circuits |
KS C IEC 60050-551-2002 | 国际电工词汇第551部分:电力电子 | International electrotechnical vocabulary-Part 551:Power electronics |
KS C IEC 60050-561-2018 | 国际电工词汇第561部分:频率控制、选择和检测用压电、电介质和静电器件及相关材料 | International electrotechnical vocabulary — Part 561: Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control, selection and detection |
KS C IEC 60050-581-2016 | 国际电工词汇第581部分:电子设备用机电元件 | International Electrotechnical Vocabulary — Part 581: Electromechanical components for electronic equipment |
KS C IEC 60050-651-2018 | 国际电工词汇第651部分:带电作业 | International electrotechnical vocabulary — Part 651: Live working |
KS C IEC 60050-701-2002 | 国际电工词汇第701章:电信、信道和网络 | International Electrotechnical Vocabulary-Chapter 701:Telecommunications, channels and networks |
KS C IEC 60050-702-2018 | 国际电工词汇第702部分:振荡、信号和相关装置 | International electrotechnical vocabulary — Part 702:Oscillations, signals and related devices |
KS C IEC 60050-704-2002 | 国际电工词汇第704章:传输 | International electrotechnical vocabulary-Chapter 704:Transmission |
KS C IEC 60050-705-2002 | 国际电工词汇第705章:无线电波传播 | International Electrotechnical Vocabulary-Chapter 705:Radio wave propagation |
KS C IEC 60050-712-2002 | 国际电工词汇第712章:天线 | International Electrotechnical Vocabulary-Chapter 712:Antennas |
KS C IEC 60050-713-2002 | 国际电工词汇第713章:无线电通信:发射机、接收机、网络和操作 | International Electrotechnical Vocabulary-Chapter 713:Radio communications:Transmitters, receivers, networks and operation |
KS C IEC 60050-714-2002 | 国际电工词汇第714章:电信中的开关和信号 | International Electrotechnical Vocabulary-Chapter 714:Switching and signalling in telecommunications |
KS C IEC 60050-715-2002 | 国际电工词汇第715章:电信网络、电信业务和操作 | International Electrotechnical Vocabulary-Chapter 715:Telecommunication networks, teletraffic and operation |
KS C IEC 60050-716-2002 | 国际电工词汇第716-1章:综合业务数字网(ISDN)第1部分:总则 | International Electrotechnical Vocabulary-Chapter 716-1:Integrated services digital network(ISDN)-Part 1:General aspects |
KS C IEC 60050-721-2002 | 国际电工词汇第721章:电报、传真和数据通信 | International electrotechnical vocabulary-Chapter 721:Telegraphy, facsimile and data communication |
KS C IEC 60050-722-2009 | 国际电工词汇第722章:电话 | International Electrotechnical Vocabulary-Chapter 722:Telephony |
KS C IEC 60050-723-2002 | 国际电工词汇第723章:广播:声音、电视、数据 | International Electrotechnical Vocabulary-Chapter 723:Broadcasting:Sound, television, data |
KS C IEC 60050-725-2002 | 国际电工词汇第725章:空间无线电通信 | International Electrotechnical Vocabulary-Chapter 725:Space radiocommunications |
KS C IEC 60050-726-2002 | 国际电工词汇第726章:传输线和波导 | International Electrotechnical Vocabulary- Chapter 726:Transmission lines and waveguides |
KS C IEC 60050-801-2011 | 国际电工词汇第801章:声学和电声学 | International Electrotechnical Vocabulary-Chapter 801: Acoustics and electroacoustics |
KS C IEC 60050-806-2002 | 国际电工词汇第806章:录音录像 | International Electrotechnical Vocabulary-Chapter 806:Recording and reproduction of audio and video |
KS C IEC 60050-807-2002 | 国际电工词汇第807部分:音频和视频信号的数字记录 | International Electrotechnical Vocabulary-Part 807:Digital recording of audio and video signals |
KS C IEC 60050-815-2009 | 国际电工词汇第815部分:超导性 | International Electrotechnical Vocabulary-Part 815:Superconductivity |
KS C IEC 60050-845-2009 | 国际电工词汇第845章:照明 | International Electrotechnical Vocabulary-Chapter 845:Lighting |
KS C IEC 60050-901-2018 | 国际电工词汇第901部分:标准化 | International electrotechnical vocabulary — Part 901: Standardization |
KS C IEC 60051-1-2013 | 直接作用模拟指示电测量仪表及其附件第1部分:定义和通用要求 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 1:Definitions and general requirements common to all parts |
KS C IEC 60051-2-2013 | 直接作用模拟指示电测量仪表及其附件.第2部分:电流表和电压表 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 2:Special requirements for ammeters and voltmeters |
KS C IEC 60051-3-2013 | 直接作用模拟指示电测量仪表及其附件.第3部分:功率表和无效功率表 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 3:Special requirements for wattmeters and varmeters |
KS C IEC 60051-4-2013 | 直接作用模拟指示电测量仪表及其附件.第4部分:频率表 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 4:Special requirements for frequency meters |
KS C IEC 60051-5-2013 | 直接作用模拟指示电测量仪表及其附件.第5部分:相位表、功率因数表和同步指示器 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 5:Special requirements for phase meters, power factor meters and synchroscopes |
KS C IEC 60051-6-2013 | 直接作用模拟指示电测量仪表及其附件.第6部分:电阻表(阻抗表)和电导表 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 6:Special requirements for ohmmeters(impedance meters) and conductance meters |
KS C IEC 60051-7-2013 | 直接作用模拟指示电测量仪表及其附件第7部分:多功能仪表 | Direct acting indicating analogue electrical measuring instruments for multi-function instruments |
KS C IEC 60051-8-2013 | 直接作用模拟指示电测量仪表及其附件第8部分:相关附件 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 8:Special requirements for accessories |
KS C IEC 60051-9-2013 | 直接作用模拟指示电测量仪表及其附件.第9部分:试验方法 | Direct acting indicating analogue electrical measuring instruments and their accessories-Part 9:Recommended test methods |
KS C IEC 60052-2003 | 用标准(空)气隙法测量电压 | Voltage measurement by means of standard air gaps |
KS C IEC 60055-1-2008 | 额定电压小于18/30kV的纸绝缘金属护套电缆(用铜芯或铝芯导线、不包括压气和充油电缆).第1部分:电缆及其附件试验 | Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV(with copper or aluminium conductors and excluding gas-pressure and oil-filled cables)-Part 1:Tests on cables and their accessories |
KS C IEC 60055-2-2008 | 额定电压小于18/30kV的纸绝缘金属护套电缆(用铜芯或铝芯导线、不包括压气和充油电缆).第2部分:通用要求和结构要求 | Paper-insulated metal-sheathed cables for rated voltages up to 18/30 kV(with copper or aluminium conductors and excluding gas-pressure and oil-filled cables)-Part 2:General and construction requirements |
KS C IEC 60059-2016 | IEC标准电流额定值 | Standard current ratings |
KS C IEC 60060-1-2001 | 高压试验技术.第1部分:一般定义和试验要求 | High-voltage test techniques-Part 1:General definitions and test requirements |
KS C IEC 60060-2-2001 | 高压试验技术.第2部分:测量系统 | High-voltage test techniques-Part 2:Measuring Systems |
KS C IEC 60060-3-2014 | 高压试验技术.第3部分:现场试验的定义和要求 | High-voltage test techniques — Part 3: Definitions and requirements for on-site testing |
KS C IEC 60061-1-2005 | 灯头、灯座及检验其互换性和安全性的量规第1部分:灯头 | Lamp caps and holders together with gauges for the control of interchangeability and safety-Part 1:Lamp caps |
KS C IEC 60061-2-2005 | 灯头、灯座及检验其互换性和安全性的量规第2部分:灯座 | Lamp caps and holders together with gauges for the control of interchangeability and safety-Part 2:Lampholders |
KS C IEC 60061-3-2005 | 灯头、灯座及检验其互换性和安全性的量规第3部分:量规 | Lamp caps and holders together with gauges for the control of interchangeability and safty-Part 3:Gauges |
KS C IEC 60061-4-2014 | 灯头、灯座及检验其互换性和安全性的量规.第4部分:指南和一般信息 | Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 4: Guidelines and general information |
KS C IEC 60062-2018 | 电阻和电容器标记代码 | Marking codes for resistors and capacitors |
KS C IEC 60063-2018 | 电阻和电容器的优先数系列 | Preferred number series for resistors and capacitors |
KS C IEC 60064-2003 | 家庭及类似场合普通照明用钨丝灯.性能要求 | Tungsten filament lamps for domestic and similar general lighting purposes-Performance requirements |
KS C IEC 60065-2013 | 家用电器的安全性 | Audio, video and similar electronic apparatus - Safety requirements |
KS C IEC 60068-1-2017 | 环境试验第1部分:总则和指南 | Environmental testing-Part 1:General and guidance |
KS C IEC 60068-2-2003 | 基本环境试验规程第2部分:试验试验试验J和指南:霉菌生长 | Basic environmental testing procedures-Part 2:Tests-Test J and guidance:Mould growth |
KS C IEC 60068-2-2014 | 环境试验.第2部分:试验.试验Ka:盐雾 | Environmental testing — Part 2: Tests — Test Ka: Salt mist |
KS C IEC 60068-2-2010 | 环境试验第2-1部分:试验试验试验A:低温 | Environmental testing-Part 2-1:Tests-Test A:Cold |
KS C IEC 60068-2-2014 | 环境试验.第2-13部分:试验.试验M:低气压 | Environmental testing — Part 2-13: Tests — Test M: Low air pressure |
KS C IEC 60068-2-2014 | 环境试验.第2-14部分:试验.试验N:温度变化 | Environmental testing — Part 2-14: Tests — Test N: Change of temperature |
KS C IEC 60068-2-2017 | 基本环境试验规程第2部分:TGESTS试验Q:密封 | Basic environmental testing procedures Part 2:TGests-Test Q:Sealing |
KS C IEC 60068-2-2010 | 环境试验第2-18部分:试验试验R和指南:水 | Environmental testing-Part 2-18:Tests-Test R and guidance:Water |
KS C IEC 60068-2-2015 | 环境试验第2-20部分:试验试验试验T:焊接 | Environmental testing-Part 2-20:Tests-Test T:Soldering |
KS C IEC 60068-2-2010 | 环境试验第2-21部分:试验试验试验U:终端和整体安装装置的坚固性 | Environmental testing-Part 2-21:Tests-Test U:Robustness of terminations and integral mounting devices |
KS C IEC 60068-2-2014 | 环境试验第2-2部分:试验试验B:干热 | Environmental testing — Part 2-2: Tests — Test B: Dry heat |
KS C IEC 60068-2-2017 | 环境试验第2部分:试验试验试验Ea和指南:冲击 | Environmental testing-Part 2:Tests-Test Ea and guidance:Shock |
KS C IEC 60068-2-2014 | 环境试验第2-30部分:试验试验Db:循环湿热试验(12h+12h循环) | Environmental testing — Part 2-30: Tests — Test Db: Damp heat, cyclic(12 h+12 h cycle) |
KS C IEC 60068-2-2014 | 环境试验.第2-31部分:试验.试验EC:主要用于设备型样品的粗处理冲击 | Environmental testing — Part 2-31: Tests — Test Ec: Rough handling shocks, primarily for equipment-type specimens |
KS C IEC 60068-2-2014 | 环境试验第2-38部分:试验试验Z/AD:复合温湿度循环试验 | Environmental testing — Part 2-38: Tests — Test Z/AD: Composite temperature/humidity cyclic test |
KS C IEC 60068-2-2018 | 环境试验.第2-39部分:试验.试验和指南:带低气压试验的温度或温度和湿度的组合试验 | Environmental testing — Part 2-39: Tests — Tests and guidance: Combined temperature or temperature and humidity with low air pressure tests |
KS C IEC 60068-2-2005 | 环境试验第2-42部分:试验试验试验Kc:触点和连接件的二氧化硫试验 | Environmental Testing-Part 2-42:Tests-Test Kc:Sulphur dioxide test for contacts and connections |
KS C IEC 60068-2-2005 | 环境试验第2-43部分:试验试验试验Kd:接触和连接的硫化氢试验 | Environmental testing-Part 2-43:Test-Test Kd:Hydrogen sulphide test for contacts and connections |
KS C IEC 60068-2-2004 | 环境试验第2部分:试验T指南:焊接 | Environmental testing-Part 2:Guidance on Test T:Soldering |
KS C IEC 60068-2-2014 | 环境试验.第2-45部分:试验.试验Xa和指南:浸入清洁溶剂中 | Environmental testing — Part 2-45: Tests — Test XA and guidance: Immersion in cleaning solvents |
KS C IEC 60068-2-2010 | 环境试验第2-47部分:试验振动、冲击和类似动态试验用试样的安装 | Environmental testing-Part 2-47:Tests-Mounting of specimens for vibration, impact and similar dynamic tests |
KS C IEC 60068-2-2017 | 环境试验第2部分:试验试验试验Sa:地面模拟太阳辐射 | Environmental testing-Part 2:Tests-Test Sa:Simulated solar radiation at ground level |
KS C IEC 60068-2-2010 | 环境试验第2部分:试验试验试验Kb:循环盐雾(氯化钠溶液) | Environmental testing-Part 2:Tests-Test Kb:Salt mist, cyclic(sodium chloride solution) |
KS C IEC 60068-2-2017 | 环境试验第2部分:试验Z/AFC和Z/BFC试验指南:组合温度(冷热和干热)和振动(正弦)试验 | Environmental testing-Part 2:Tests-Guidance to tests Z/AFc and Z/BFc:Combined temperature(cold and dry heat) and vibration(sinusoidal) tests |
KS C IEC 60068-2-2015 | 环境试验第2-54部分:试验试验试验Ta:用湿平衡法对电子元件进行可焊性试验 | Environmental testing-Part 2-54:Tests-Test Ta:Solderability testing of electronic components by the wetting balance method |
KS C IEC 60068-2-2018 | 环境试验.第2-55部分:试验.试验Ee和指南.包括弹跳的松散货物试验 | Environmental testing — Part 2-55: Tests — Test Ee and guidance — Loose cargo testing including bounce |
KS C IEC 60068-2-2003 | 环境试验第2-57部分:试验试验试验Ff:振动时程法 | Environmental testing-Part 2-57:Tests-Test Ff:Vibration -Time-history method |
KS C IEC 60068-2-2007 | 环境试验第2-58部分:试验试验试验td:表面安装装置(SMD)的可焊性、耐金属化溶解性和耐焊接热的试验方法 | Environmental testing-Part 2-58:Tests-Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices(SMD) |
KS C IEC 60068-2-2010 | 环境试验第2部分:试验试验试验Ke:流动混合气体腐蚀试验 | Environmental testing-Part 2:Tests-Test Ke:Flowing mixed gas corrosion test |
KS C IEC 60068-2-2010 | 环境试验第2部分:试验方法试验Z/ABDM:气候顺序 | Environmental testing-Part 2:Test methods-Test Z/ABDM:Climatic sequence |
KS C IEC 60068-2-2015 | 环境试验第2-6部分:试验试验Fc:振动(正弦) | Environmental testing — Part 2-6: Tests — Test Fc: Vibration(sinusoidal) |
KS C IEC 60068-2-2014 | 环境试验第2-64部分:试验试验Fh:振动、宽带随机和指南 | Environmental testing — Part 2-64: Tests — Test Fh: Vibration, broadband random and guidance |
KS C IEC 60068-2-2003 | 环境试验第2部分:试验方法试验Fg:声诱发振动 | Environmental testing-Part 2:Methods of test-Test Fg:Vibration, acoustically induced |